Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
HandyScope HS5: 200 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-220XM-W5
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 200 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
product
VME64 to USB 2.0/Optical Link Bridge
VX3718
The VX3718 is the new VME to USB 2.0/Optical Link Bridge that fully replaces the VX1718 (VME-USB) and V2718 (VME- CONET) models. The Bridge Implements a VME master controlled by a PC via USB 2.0 and Optical Link (CAEN CONET protocol) including all the functions of its two predecessors in a unique device.
-
product
3.5" Embedded SBC With Intel® Celeron® Processor N2807, LVDS/VGA/HDMI, LAN And Audio
CAPA848
*Intel® Celeron® processor N2807 (1.58 GHz)*1 DDR3L-1333 SO-DIMM, up to 8GB*4 USB 2.0 ports*4 COM ports*2 PCI Express Mini Card slots and 1 SIM slot*1 Gigabit Ethernet port*LVDS/VGA/HDMI with dual-view supported
-
product
WiFiScope WS6: 1 GS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-1000XM-W5
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.With a WAN connection, worldwide measurements can be performed. Specific knowledge on networks is not required. The Multi Channel software gives an overview of the available USB instruments and network instruments. Simply tick the instrument and measuring can start. The WiFi oscilloscope has the following advantages: fully wireless measurements via WiFi are performed (galvanically isolated) because of the built-in battery mobile measurements are possible, e.g. on transport systems and moving installations LAN and WAN data acquisition is available for long distance measurements continuous realtime highspeed data acquisition over both WiFi and LAN/WAN are available USB measurements for stand-alone applications and highspeed data acquisition up to 200MSa/s.
-
product
USB Modular Digital Multimeter, 5 digit
U2741A
The Keysight U2741A USB Modular Digital Multimeter provides a broad range of measurement functions, including temperature and frequency. The U2741A is a 5.5-digit resolution digital multimeter that is able to capture up to 100 readings/sec. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity allowing users to set up and configure their tests swiftly with its plug and play feature.
-
product
USB Compliance Testers
The Packet-Master USB-PET is a Protocol and Electrical Tester capable of performing thesuite of tests defined in the USB-IF specifications for OTG 2.0, and Battery Charging. The PET tester hardware was designed in co-operation with the USB-IF USB On-The-Go Work Group, and the Battery Charging Work Group.
-
product
Pico-ITX
RSB-3410
*NXP ARM Cortex-A9 i.MX6 Dual Lite 1 GHz high performance processor*Onboard DDR3 1 GB, 4 GB eMMC Flash*Supports OpenGL ES 2.0 and OpenVG 1.1 hardware accelerators, full HD 1080p video codecHDMI 1920x1080*Single Channel 18/24 bit LVDS*Dual mini-PCIe for WIFI/3G support*1 USB 2.0, 1 USB OTG client*Multiple OS support in Linux/Android
-
product
Remote Spectral Detector
CSS-45
The CSS-45 detector incorporates a powerful microprocessor which performs not only data acquisition but also all necessary lighting calculations. Both USB 2.0 and RS 485 interfaces are standard enabling the flexible configuration of single and multi-detector based systems. An optional software development kit supports integration into third party application software. With its wide spectral range from 360 nm to 830 nm the CSS-45 is ideal, for example, as a high accuracy photometric and colorimetric detector (according to CIE S023).
-
product
COM Express Type 10 Mini Application Board With LVDS, VGA, Dual LAN And Audio
CEB94018
*84 x 55 mini size form factor*2 GbE LAN*SATA and mSATA*LVDS and VGA*6 USB 2.0*2 PCI Express Mini Card slots
-
product
Saluki S87235 Series USB Average Power Sensor (max. 50GHz)
S87235 series USB average power sensor is a diode-detection type high-precision, large dynamic range average power measuring instrument based on the USB 2.0 interface, which can accurately measure the average power of signals in various formats. The frequency range of S87235 series average power probe covers 10MHz-50GHz, and the average power measurement accuracy can reach ≤±0.20dB.
-
product
Robust DIN-rail Fanless Embedded System With Intel® Atom® Processor E3815/E3827, 4 COM, 2 LANs, DIO And RTC
ICO300
With din-rail, fanless and rugged design, the ICO300 embedded system utilizes low power 22nm Intel® Atom™ processor E3815 (1.46 GHz) and supports DDR3L system memory maximum up to 4GB, delivering high performance at competitive price. This intelligent Intel® Atom-based IoT gateway solution supports complete expandability and features, including wireless support, four RS-232/422/485 ports, two isolated Gigabit Ethernet ports, two high-speed USB 2.0 ports, RTC battery function, and wide range 12-24VDC power input with terminal block. The ICO300 is also Axiomtek's first IoT gateway solution certified by Microsoft Azure IoT. The application-ready ICO300 simplifies the development process and achieves accelerated business transformation of IoT environment. This intelligent IoT gateway system provides a perfect solution for IoT & M2M, industrial and embedded applications such as power plant automation, facility monitoring systems, intelligent transportation systems and other harsh environments.
-
product
MiniPCI Express to USB 3.x Adapter
SKU-089-14
MiniPCI Express to USB 3.x Adapter allows connection M.2 modules with M.2 (B key) to a MiniPCI Express circuit. Adapter can be installed in Full size or Half size MiniPCI Express circuits and supports USB 3.x, USB 2.0 interfaces.
-
product
USB 2.0 Protocol Analyzer
Mercury T2
The Mercury T2 is the industry's smallest, most affordable hardware-based USB 2.0 protocol analyzer that combines the defacto standard CATC Trace display with powerful analysis features. The pocket-sized Mercury T2 is bus powered and is controlled using any Windows PC. With comprehensive triggering, the Mercury T2 provides much of the same lab quality protocol analysis capabilities offered in Teledyne LeCroy's top-of-the-line USB analyzers.
-
product
Multi-protocol USB Type-C Analyzer
Type-C Tracker
Protocol and Electrical Analysis Tool for Type-C Communications Standards. All-in-One: Concurrent and tightly synchronized capture of USB Power Delivery protocol, Type-C voltage tracking (Vconn, Vbus, SBU, and CC), USB 2.0, Thunderbolt 3 UART and DisplayPort auxiliary (AUX) signaling over the Type-C SBU lines, alternate (ALT) mode support for DisplayPort, HDMI, and Thunderbolt, and capture and decoding of Serial Wire Debug (SWD) protocol, UART, Serial Peripheral Interface (SPI) I2C vendor-specific protocols, and Type-C Port Controller Interface traffic over I2C.
-
product
LGA 1700 Intel® 12th Gen. Core™ ATX Server Board with 4 x DDR5, 5 x PCIe(1 x Gen 5, 3 x Gen 4, 1x Gen 3), 7x USB3.2, 4xSATA3, Quad/Dual LANs, and IPMI
ASMB-788
- LGA 1700 Intel® 12th Gen. Core™ i9/i7/i5/i3 processors with W680 chipset- DDR5 ECC/Non-ECC 4400/4000/3600 MHz UDIMM up to 128 GB- One PCIe x16 (Gen 5) and four PCIe x4 (3 x Gen 4 & 1 x Gen 3) slots- Triple displays - DVI-D, VGA, and HDMI 2.0 ports- Four SATA 3 ports and seven USB 3.2 ports- One M.2 2280 (PCIe x4)- Rackmount optimized placement with positive air flow design- 0 ~ 60 °C (32 ~ 140 °F) ambient operating temperature range
-
product
cRIO-9048, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller
785619-02
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller - The cRIO-9048 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
product
Arbitrary Waveform Generators
M531
The M531 is a single channel USB arbitrary waveform generator compatible with USB 2.0 and USB 1.1 interface. The generator has two outputs: both generate same waveform, but with different peak-peak voltage. The low level output has 50ohm output impedance and maximal peak-peak voltage of 9V. There is no external power supply required to enable low level output (it is powered from USB bus).
-
product
ARM 9 System on Module
MS 1515
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
product
WiFiScope WS6+EMI: 1 GS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-1000XME-W5
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.
-
product
USB Modular Isolated Digital Input/Output
U2600A Series
The Keysight U2600A Series U2600A Series USB Modular Isolated Digital Input/Output Devices are high performance modules that comprise of three models U2651A isolated 32-bit DI and 32-bit DO, U2652A isolated 64-bit DI and U2653A isolated 64-bit DO. The U2600A Series provides up to eight channels with 64-bit of high density opto-isolated digital input and digital output for USB 2.0 interface-based industrial applications like driving relays, actuator, or valve. The U2600A Series targets a wide range of application both in industrial automation and education.
-
product
WiFiScope WS5: 200 MS/s 250MHz BW, 2 Channel, Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
WS5-220XM-W5
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.With a WAN connection, worldwide measurements can be performed. Specific knowledge on networks is not required. The Multi Channel software gives an overview of the available USB instruments and network instruments. Simply tick the instrument and measuring can start. The WiFi oscilloscope has the following advantages: fully wireless measurements via WiFi are performed (galvanically isolated) because of the built-in battery mobile measurements are possible, e.g. on transport systems and moving installations LAN and WAN data acquisition is available for long distance measurements continuous realtime highspeed data acquisition over both WiFi and LAN/WAN are available USB measurements for stand-alone applications and highspeed data acquisition up to 200MSa/s.
-
product
COM Express
COM Express defines standardized footprints and pin-outs for Computer-on-Modules. With the Revision 2.0, PICMG added the compact footprint (95x95mm) to the basic footprint (125x95mm) and extended the pin-outs being future-proof. New Digital Display Interfaces (DDI) and super-fast USB 3.0 are available. The new Pin-out Type 10 in COM Express Revision 2.0 supports perfectly modules in the COM Express mini footprint (84x55 mm).
-
product
cRIO-9056, 1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 75T FPGA, 8-Slot CompactRIO Controller
786426-01
1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 75T FPGA, 8-Slot CompactRIO Controller - The cRIO-9056 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers one Gigabit Ethernet port, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
High-Speed USB 2.0 JTAG Controller
USB-1149.1/1E
The USB-1149.1/1E is a high-performance plug-and-play IEEE-1149.1 Boundary-Scan (JTAG) controller for the Universal Serial Bus (USB 2.0). The USB-1149.1/1E is a high-speed device compliant with Revision 2.0 of the USB Bus Specification.
-
product
150MHz Isolated Oscilloscope
M774
The M774 is a dual channel USB oscilloscope compatible with USB 2.0 and USB 1.1 interface. The computer is isolated up to 500Vp from the measuring circuits of the oscilloscope. The ease of installation and connection to computer makes M774 extremely portable. The device is connected to computer using standard USB 2.0 cable and is powered directly from computer. The maximum power consumption of 2.35W makes this instrument highly usable with battery-powered notebooks.
-
product
USB Protocol Verification System
Voyager M310e
The Voyager M310e is Teledyne LeCroy's flagship USB protocol verification system designed for USB 2.0, USB 3.2, Type-C, and USB Power Delivery. Offering the industry's highest fidelity probe design, flexible traffic generation, and a range of turnkey Compliance packages, the Voyager M310e is the most complete platform for cradle-to-grave USB design verification.
-
product
PXIe-8880, 2.3 GHz Eight-Core PXI Controller
783513-33
PXIe, 2.3 GHz Eight-Core PXI Controller—The PXIe‑8880 is an Intel Xeon 8‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8880 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive and other peripheral I/O.
-
product
USB-C® – USB 2.0 Receptacle HS SQ Test
AUT17037
This product is designed for USB-C USB2.0 Plug Host/Device Electrical Test.
-
product
PXIe-8881, 3.9 GHz 8-Core PXI Controller
787805-33
PXIe, 3.9 GHz 8-Core PXI Controller - The PXIe-8881 is an Intel Xeon 8-Core embedded controller for PXI Express systems. You use the PXIe-8881 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8881 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive and other peripheral I/O, such as two Thunderbolt 3 ports. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
product
Open Pluggable Specification (OPS) Digital Signage Player With 4th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® H81 And TPM 1.2
OPS883-H
The OPS883-H OPS-compliant digital signage player is powered by the 4th generation Intel® Core™ i7/i5/i3 processor (codename: Haswell) with the Intel® H81 chipset. It has one 204-pin DDR3 SO-DIMM socket with maximum up to 8 GB. It offers stunning 4K Ultra High Definition (UHD) content via a HDMI port. The Intel® Core-based OPS883-H is ideal for multi-display applications in airport information board, shopping mall, corporate, education, hospitality, religious organization, bank, retail store, restaurant, performing art center and many more. This smart pluggable signage module is connected to OPS-compliant display via a standardized JAE TX-25 plug connector, and includes DisplayPort, UART, audio, USB 3.0 and USB 2.0 signals. To fill different application needs, the signage unit reserves a wide choice of I/O ports on front panel, including one USB 3.0 ports, two USB 2.0 ports, one COM port, audio (in/out) and a Gigabit Ethernet port. This slim-type OPS system has one internal PCI Express Mini Card slot to connect Wi-Fi or 3G/ LTE modules to satisfied users wireless needs. It features one easy-to-access 2.5” SATA HDD as storage device. Also, it supports TPM 1.2 feature which is designed to secure system.
-
product
USB Modular Source Measure Unit
U2722A
The U2722A USB Modular Source Measure Unit is a 3-channel 20V/120mA that can operate in a 4-quadrant operation. The channels could be connected in series or in parallel to achieve up to 60 V/360 mA. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity allowing users to set up and configure their tests swiftly with its plug and play feature.
