Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
EBIRST 50-pin D-type Test Tool
93-005-001
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
Lightwave Transmitter Analyzer Bundle
N4364A
The N4364A Lightwave Transmitter Analyzer Bundle consists of a calibrated OE-converter - the N4377A Lightwave Detector - and Vector Network Analyzer - either from the PNA- or from the Streamline Series USB-family - and is a cost-effective solution to test the frequency response of optical transmitters such as directly modulated lasers diodes (DMLs), Mach-Zehnder Modulators (MZMs) or other devices.
-
product
Motor Octane Testing
DewTrak II MO
DewTrakII MO dew point/humidity transmitter is an optical chill mirror hygrometer designed to continuously measure the moisture content and Barometric pressure in the motor octane testing process. It is used to monitor and ensure compliance with test
-
product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
product
Optical Switch Boxes
An optical switch box is needed so that automated test platforms can permit the system to measure the performance of transmitters and receivers at multiple wavelengths or channels. The MLO4034 Optical Switch Box incorporates a WDM demultiplexer, integrated power meters, variable optical attenuators, and optical switches to form an integrated switch matrix. It enables receivers and transmitters to be tested at up to four wavelengths or channels.
-
product
110 GHz Lightwave Component Analyzer
N4372E
The N4372E lightwave component analyzer helps you with optoelectronic tests with its measurement capability of 110 GHz in an extended wavelength range. It also offers RX testing up to 110 GHz in the full 1260 nm to 1620 nm range. It has a built-in optical power meter that enables you to check and control the operating power. The N4372E lightwave component analyzer's optical transmitter input port connects to an auxiliary tunable laser to verify S-parameters over wavelength.
-
product
Pressure and Vacuum Instruments
We offer a vast selection of pressure and vacuum instruments for industrial, process, research, and laboratory applications. These instruments test, measure, and can control different aspects of a process where pressure, vacuum, or both are present. Our wide selection includes mechanical and digital gauges, transmitters and transducers, switches, controllers, air and gas regulators, and I/P transducers.
-
product
BERT Measurement Solutions
Bit error rate testers (BERTs) are usually the initial step for communications testing. These instruments generate digital test patterns, typically pseudorandom binary sequences (PRBSs), that drive devices under test (DUTs). Following the transmission of the signal through the link, the receiver in the BERT captures the signal. This setup can be used for multiple testing purposes, such as to evaluate the performance of a transmitter, a receiver, or an optical link.
-
product
Reference Transmitter
81492A
Keysight's 81492A Reference Transmitter is designed to offer excellent eye quality for NRZ and PAM4 signals at baud-rates up to 56 Gbaud and can serve as universal single-mode E/O converter. In addition to the internal lasers at 1310 & 1550 nm, an external optical input for usage with tunable laser sources is available. It is fully integrated into Keysight’s Optical Receiver Stress Test solutions to address test requirements of IEEE 802.3 10,40,100 and 400GBASE optical standards.
-
product
Four-Port Tunable Laser System Source
N7714A
The Keysight N7711A and N7714A tunable lasers are single-port and four-port sources, available with C-band or L-band wavelength coverage. The narrow linewidth and offset grid fine-tuning capability make them ideal sources for realistic loading of the latest transmission systems. All models can reach any wavelength point within their specified wavelength range just like all other Keysight tunable lasers. In this mode, code compatibility with existing test setups based on Keysight's range of full-size and compact tunable lasers is a great asset. In system loading applications, it may be preferable to grid-tune the lasers like system transmitters, simply by changing the channel index. The channel grid is adjustable to standard ITU-T grid spacing like 50 GHz, and to arbitrary grids. Likewise, the zero frequency (base channel) of the chosen grid is adjustable. A 12 GHz fine-tuning range allows de-tuning the frequency.
-
product
Coaxial Dual-Directional Coupler, 2 GHz to 18 GHz
772D
The Keysight 772D is a high-performance, dual-directional coupler designed for broadband swept measurements in the 2 to 18 GHz range. This coupler can be combined with Keysight power sensors and power meters for reflectometer applications. Forward and reverse power measurements on transmitters, components, or other broadband systems are made simpler using the Keysight 772D. The broadband design allows the use of a single test setup and calibration for tests spanning the entire 2 to 18 GHz range.
-
product
PhyView Analyzer
PVA-3000
Connects up to 24 10/100/1000Base-T ports and provides access to the PHY Performance Test Suite supporting one-click, fully automated transmitter, receiver, and, auto-neg testing.
-
product
ARINC-429 Module
M4K429RTx
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
product
IQ Data Bandwidth Up To 4 GHz
S93051B
with a single connection to a PNA family network analyzer utilizing the industry-standard PathWave 89600 VSA (VSA) software for 5G transmitter test. The VSA IQ data link feature in S93050B allows you to send IQ data from the PNA to the VSA software and analyze symbol EVM, AM-AM, and AM-PM.
-
product
RF & Microwave
Data Patterns has a strong RF and Microwave engineering capability, featuring a team of enthusiastic engineering talent, substantial investments in RF test and measuring instruments, and attitude to utilise the latest technologies.An in-house manufacturing capability and an insatiable demand for fulfilling requirements of Radar, Electronic Warfare and Communication domains, Data Patterns has developed a whole line of building blocks including TR Modules, Up and Down Converters, Power Amplifiers, Transmitters, Combiners and Dividers for specific requirements. A list of products is given below.
-
product
IQ Data Bandwidth Up To 1.5 GHz
S93050B
Make multiple measurements of active device distortion analysis with a single connection to a PNA family network analyzer utilizing the industry-standard PathWave 89600 VSA (VSA) software for 5G transmitter test. The VSA IQ data link feature in S93050B allows you to send IQ data from the PNA to the VSA software and analyze symbol EVM, AM-AM, and AM-PM.
-
product
Low PIM Coaxial Switch, DC to 4 GHz, SP4T
87104P
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104P is a low PIM SP4T coaxial switch, operating from DC to 4 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Telemetry Transmitter for FM with up to 3 Bands
LS-11-F
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.
-
product
Multi-Mode Test Transmitter to 6 GHz
WTX-610 iLLUMINATOR
Wideband operation up to 6 GHz allows the iLLuminator to address all your future needs of signal generators / test transmitters even over unlicensed bands for LTE-U and LAA or the CBRS Band. These features combined with the ultra-portable handheld form factor and innovative touch interface for maximum ease of use make the WTX-610 iLLuminator a convenient choice for laboratory users as well as field applications such as DAS & Small Cells radio planning and testing.
-
product
PCI Express® Electrical Performance Validation and Compliance Software
D9040PCIC
D9040PCIC PCI Express Transmitter Test Compliance Software for PCI Express 4.0 (PCIe 3.x, 2.x and 1.x also supported).
-
product
Portable Telemetry Systems
Lumistar’s portable receivers and test transmitters take the state of the art technology found in the PCI receivers and simulators and install it into a hand held units. Our luggable Telemetry Systems can be configured using our card level products into unique custom solutions.
-
product
ARINC-429 Multi-Channel Test & Simulation Module for Excalibur 8000 Family of Carrier Boards
M8K429
The M8K429 is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 8000 family of carrier boards. The module supports up to five ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word. The receivers allow for filtering and multi-storage modes of Data Words. The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention.The M8K429 comes complete with C-driver software library including the source code.
-
product
Pneumatic Test Pump Kit
700HPPK
The Fluke Calibration 700HPPK Pneumatic Test Pump Kit generates and adjusts pneumatic pressures up to 21 MPa (3000 psi), without requiring a nitrogen bottle or other external pressure supply. It supplies pressure to devices under test (DUTs) that include transmitters, controllers, pilots, digital and analog gauges, and more. It’s the perfect solution for generating high pressure in the field, where conditions and operating surfaces can vary. The 700HPPK is the ideal choice for calibration technicians, test engineers, and instrument technicians working in industries like natural gas transmission and distribution, process, aerospace and defense, who need a simple-to-use, safe and portable pressure source that they can depend on in a wide variety of conditions.
-
product
Terminal Power Meter
TPM-50A
ShinewayTech@ TPM-50A Terminal Power meter can test (1) Average power range: -40 dBm~+20 dBm；(3) Modulation bandwidth: 5MHz；(3) Continuous signal and burst signal test. Highly accurate power measurement CW and digital modulated signal (For example: GSM/EDGE, CDMA/EV-DO, WCDMA/HSDPA, WiMAX, and TD-SCDMA). It is very important to test that if the transmitter is at a specified level or not. For example, the tester needs to test the output power of base station. Because the lower output power produces the larger coverage area to cause call interruption.
-
product
Low PIM Coaxial Switch, DC to 26.5 GHz, SP4T
87104R
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104R is a low PIM SP4T coaxial switch, operating from DC to 26.5 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Low PIM Coaxial Switch, DC to 20 GHz, SP6T
87106Q
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87106Q is a low PIM SP6T coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
CW Transmitters
The Praxsym CW Transmitter is a complete, portable continuous wave test source. Used as an input source to test a distributed antenna system, the Praxsym CW Transmitter can provide test signals aiding in the design and optimization of in-building and outdoor networks.
-
product
Low PIM Coaxial Switch, DC to 20 GHz, Matrix
87606Q
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87606Q is a low PIM matrix coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency, and ultimately maximizes test throughput.
-
product
Whole Body EM Phantoms
EM - PHANTOM
Schmid & Partner Engineering AG
The POsable Phantom for Electromagnetic sYstems Evaluations (POPEYE) is an anatomically correct human phantom based on a torso shell w/ head with posable arms, hands and legs. This radio frequency (RF) human has been designed to meet the requirements for test configurations for which the effects of the body on the EM performance cannot be neglected, such as operating tablet and laptop computers and other body-mounted transmitters. With a simple adjustment (one tightening screw), the arms, hands and legs can be positioned accordingly for conducting simulations of any usage or operation (standing, sitting, arms raised, talking position, etc...).
-
product
Cable Identification & Phasing
VCi-3™
The VCi-3™ system is designed for cable and phase identification, mainly for installation or maintenance purposes on three-phase electrical networks during power shutdowns.The transmitter module injects a low current on the cable conductors by direct contact or magnetic clamps methods. A voice message is recorded by the user and will be transmitted along with digital signals. Groundings stay connected at both ends of the three-phase circuit during the test. The detector module is used at the other end of the cable system.
-
product
Digital Wideband Transceiver Analysis
S94610B
Digital Wideband Transceiver Analysis is an add-on software to Device Measurement eXpert (DMX) that adds cross-domain stimulus response measurements for digital/RF mixed-signal device characterization. Included Waveform Creator helps define digital IQ test stimulus waveforms that are used in the RF signal generators for receiver tests or downloaded to the digital-to-analog converters for transmitter tests. The DUT control is customizable to accommodate various data converters and transceiver types by defining device operation settings, transmit/receive switching, reading and writing digital IQ waveform from and to DUTs. Acquired RF or digital data is processed in the VNA’s applications for faster, accurate measurements and analysis.
