Filter Results By:
Products
Applications
Manufacturers
Surge Testers
Analyze device performance under a sudden increase of electrical power.
See Also: Hipot Testers, Impulse Winding Testers
- PJ Electronics, Inc.
product
Signature Model Surge Testers
SP
Surge / DC Hi-Pot testing capabilities. Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope plus a DC Hi-Pot Tester. DC Hi-Pot testing with dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip. This dual tester combo is still capable of testing 3 phase motors with or without rotors.
-
product
Automated Tester
With high labor costs in Europe and the US, and the surge in labor cost in Asia, automated test solutions are in demand. Automated systems also improve traceability and reduce operator mistakes.The combination of automation with high throughput test systems is perfect to extend the usage of Flying Probe Testers to mid size production/sample volumes.
-
product
EMC Testers
The KES7000 System is a conductive immunity test system that is fully compliant with ISO7637-2 and ISO7637-3, international standards for EMC testing required for automotive electronic components. This system consists of the KES7700 Series Transient Surge Tester, KES7400A Series Voltage variation simulator and KES7100 application software dedicated to the KES7000 system. This product configuration supports JASO standards and the special test requirements of car manufacturers with options or custom orders.
-
product
DiodeTester
FECPLS500
Frothingham Electronics Corporation
The PLS500 automatic tester is designed primarily to do SURGE testing either as single pulses or with Forward and Reverse bias, according to methods 4066-1 or 4066-2. In addition, it can also test VF with rectangular pulses and THERMAL RESPONSE either in DVF (mV) or degrees per watt. All three test types may be performed in a single test program.
-
product
Motor Tester and Analyzer
ITIG
The iTIG III is the industry’s most advanced electric motor tester and winding analyzer. Bringing confidence to motor repair companies, industrial end users, OEMs, and manufacturers of rotating equipment, the iTIG III features over 20 high- and low-voltage tests including high frequency surge and partial discharge.Choose multiple tests to run automatically in a sequence or select single tests. Report results with the easiest to use instrument available. Manually operate voltage dial or set up for automatic operation. Carry the iTIG III in the field or use it as a benchtop device. Connect to an external portable power pack for testing up to 40kV. The iTIG III is the most versatile and easy-to-use tester available.
-
product
High Voltage EMC Surge Generator
TM510
TM510 Surge Generator is mainly used for testing power cable high-resistance and arc-over fault whose grade range is 0-10kV, co-operating with cable fault tester and locating devices to test and locate faults. If the user choose the professional digital milli-ampere-meter, as for cable with grade range about 0- 6kV, the instrument can also be used to do DC&voltage resistance test and current leakage test after the fault is repaired. The instrument is internally equipped with voltage-rise rectifying and discharging device, has complete functions, and is also convenient and safe to be wired and operated.
-
product
Automotive Transient Surge Simulators
ISS/JSS Series
Simulator to reproduce various transient surge phenomena which are generated in vehicles and defined in the international standard ISO-7637-2 Standard for evaluating automotive electronics immunity. Please contact us for transient testers to perform testing to manufacturers' private standards.
-
product
Battery Cell Surge Tester
Chroma 19311
Chroma Systems Solutions, Inc.
The 19311-10 has 10 channels, which can test up to 9 battery cells via scanning test, with a single unit. It can support up to 25 channels for testing up to 24 cells in a sequence by connecting with an external scanner (A190362). The test speed of the multicell scanning test by 19311-10 is extremely efficient, saving test time, and decreasing labor costs. It also increases the production capacity of the production line.
-
product
Digital Surge Tester
10KV, 12KV & 15KV
The Digital Surge Tester is designed specifically to test the coils and windings of Medium range AC Rotating machines ranging up to 6.6KV. The Surge Tester has an Embedded Industrial PC with 8 inch Touch screen Display and software to Store, Recall and Print the Test Reports.
-
product
Static Electric Motor Analyzers
Baker Instruments’ static motor test equipment is the industry-leading suite of products for detecting weaknesses and faults in the insulation systems of electric motors, generators and coils. Employing both low-voltage and high-voltage tests – such as Baker’s signature surge test - these essential troubleshooting and predictive maintenance tools allow maintenance professionals to assess any need to maintain or replace specific motors and generators that support their business. Equally at home in the motor repair shop or on a plant floor, these testers ensure that the electrical condition of your rotating machinery is understood.
-
product
High Voltage Surge Current Monitors
HVSCM
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.
-
product
Surge Suppressor Tester
(SST) 450
The ATSI SST-450 Surge Suppressor Tester is designed to quickly and easily test allcommonly used transient voltage suppressors: metal-oxide varistors (MOVs), gas-discharge tubes (GDTs), silicon avalanche diodes (SADs), thyristor surge protective devices (TSPDs), and hybrid devices.
-
product
Surge Testers
MTC 2
Advanced automatic high precision electrical winding testers for testing products like alternators, stators, transformers, armatures and motors. Available as static or portable units from 6-50 kV.
-
product
Battery Tester
G5.BT
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
product
Digital Surge Tester
KT-905D
Surge Tester of KAST is divided for the use of 3¡40 §Ç by output voltage, and subdivided into type C of manual decision type, type A of auto decision type, type L of exclusive use for low inductance product test and type P loading printer which can printout its wave form and digital scope. Surge test requires only 0.5 second. Because Surge tester already performs 30 times of Impulse voltage test only for 0.5 second. Turn-to-turn short : phenomenon shorted between the side coils.
-
product
Smart Surge Protectors
SSP-30X
Progressive Industries Smart Surge Protectors (SSP) are portable RV surge protectors with the added benefit of a built-in polarity tester. The built-in surge indicator notes the condition of the surge protector. Additionally, the polarity tester (dual line for 50A) checks the status of the power source prior to use, Sleek, compact, portable design makes it easy to use and store. Designed for outdoor use. No installation required.
-
product
3KV Digital Armature Surge Tester
D-3KAT
The Digital Armature Surge Tester with bar-to-bar test is a cost-effective solution to check the quality of Small to Large range of DC Traction Motors ideally suited for Railways. The Bar-To-Bar Test is provided to test the Low impedance of the Series wound Armatures and Field coils of DC Traction Motors. The Surge Tester has an Embedded Industrial PC with 8 inch Touch screen Display and software to Store, Recall and Print the Test Reports.
-
product
Transient Immunity Tester
KES7700
Transient Immunity Tester KES7700 Series are transient surge tester that utilizes a compact unit system. A surge generator circuit is installed for each pulse unit as the tester meets the requirement of ISO7637-2, ISO7637-3, ISO16750-2, JASO D001, SAEJ1113, and other standards. The KES7700 Series meets a broad range of independent automobile manufacturer standards as well.
-
product
High Voltage Surge Testers
HVST
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
product
IEC 61000-4-5 EN61000-4-5 Lightning Surge Tester, Surge Generator
506AX
Shenzhen Chuangxin Instruments Co., Ltd.
Automatic lightning surge generator (or Lightning surge immunity) is used to assess the power cord and connect the internal switch stood in line to connect the internal switch to provide a common basis for switching the natural world and lightning caused by the high-energy transient interference performance. Performance fully meets the IEC 61000-4-5, EN61000-4-5 and GB/T17626.5 standards.
-
product
Digital High Frequency Surge Testers
C Model
These Digital High Frequency Surge Testers are the ultimate in ruggedness & durability. Fourteen / sixteen gauge steel construction and mobility on 6" heavy duty rubber wheels makes it a favorite for use in harsh industrial environments. The performance of PJ's exclusive/unique High Frequency Technology is capable of testing the integrity of any turn-to-turn insulation, including low inductance windings.
-
product
Surge Tester (Impulse Winding Tester)
SS6815 / SS6815F
Surge testers (impulse winding tester) is used for testing and check the insulation grade of turns between turns, insulation grade of layers between layers, insulation grade of windings between turns. It is used widely for transformer, current sensor, voltage sensor, relay, contactor, inductor, motor, generator, valve coil, voice coil, etc.
-
product
Ultra-Compact Immunity Tester
AXOS5
The AXOS5 is an ultra-compact immunity tester that performs all the most commonly used transient immunity tests, including Surge, EFT, Dips/Interrupts and AC/Surge Magnetic Field. The simplified user interface provides quick selection of tests and test levels, and even lets you change test parameters “on the fly” while running a test.The actual EUT power mains voltage and current are indicated in the display. Using the Electronic-Fuse function, the user can set an upper limit for EUT power mains current. This feature is useful to protect the EUT from unnecessary damage.Whether you test to the IEC 61000 series “CE Mark” standards, the IEC 60601 Medical Device standards, or any number of telecom and product specific standards, the AXOS5 tester is your one stop test station for everything from precompliance to full compliance to product development testing.A wide range of cost-efficient Coupling / Decoupling Networks for symmetrical and asymmetrical data- and signal-lines is available as an option.
-
product
Signature Surge Tester
TSM
Compact cabinet that contains a multi-position carry/tilt handle and a rear plastic snap-on cover for cable storage and transportation in the shop or in the field. Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope and includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
product
Multi-Operational Surge Tester
M Model
Portable compact Multi-Operational Surge Tester that contains a multi-position carrying/tilt handle and a rear plastic snap-on cover for cable storage and transportation in the shop or field. The "M" is the perfect choice for your complete preventive/predictive maintenance testing - DC Hi-Pot testing, handheld resistance meter* testing and the capability of testing fully assembled grounded motors without rotating the rotor position.
-
product
SPD High, Medium, and Low Voltage TOV Test Equipment
Shanghai Guantu Technology Co., Ltd.
The high (medium) voltage TOV tester is used for transient overvoltage tests caused by faults in high and medium voltage systems such as surge protectors (SPDs), and can also be used for other scientific research tests.standardGB/T 16927-1997 High voltage test technology.GB18802.1-2011 Surge protective device (SPD) for low-voltage power distribution system Part: Performance requirements and test methods.IEC61643-1:2005 (Surge protective devices connected to low-voltage power distribution systems part 1: Performance requirements and testing methods)TOV fault test equipment1. Three-phase isolation test transformer2. Single-phase test transformer3. Low voltage switchgear4. Power controller5. Test voltage and current measurement6. Sample box
-
product
Smart Surge Protector
SSP-50X
Progressive Industries Smart Surge Protectors (SSP) are portable RV surge protectors with the added benefit of a built-in polarity tester. The built-in surge indicator notes the condition of the surge protector. Additionally, the polarity tester (dual line for 50A) checks the status of the power source prior to use. Sleek, compact, portable design makes it easy to use and store. Designed for outdoor use. No installation required.
-
product
Surge Tester
Qingdao AIP Intelligent Instruments Co., Ltd
Surge tester able to test various coils, motor, stator winding, relay/contactor coil, electric magnetic valve coil etc. and can be applied for maintenance, production line, lab and QC etc. Extension: single surge test or multiple tests options.Large storage: up to 1000 test groups can be established.Automatic determine: manual or auto test mode options and test results would be determined automatically.Support both touch screen and numeric keyboard operating.Data analysis: data can be exported in CSV format by USB flash drive.Surge determine items: area, area difference, corona, and phase.100MHz sampling frequency.3KV and 5KV voltage options.Voltage closed loop feedback ensures test precision.User permission management.Support MES connection (manufacturing execution system).
-
product
2 Piece Portables
H Model
H models are "2 piece" versions of the Signature ("S") Models. These compact two piece portable high frequency digital surge testers come complete with a Tektronix Type TDS1002, fully digital storage oscilloscope, 10' long test cables and a soft carrying case with a shoulder strap.
-
product
High Frequency Digital Surge Tester & DC Hi-Pot Tester
SPM
High Frequency Digital Surge Tester and DC Hi-Pot Tester (similar to the "SP" Model) together in a compact cabinet. Take this portable tester to your test site and accurately perform Surge, Hi-Pot, PI and Resistance Tests.
-
product
Stator & Coil Testing
Electronic Systems of Wisconsin, Inc.
ESW Stator Test Systems come fully equipped with the latest industry features. The on-screen display in our testers allows the operator to visually see the part lead hook-up to the tooling connections. Our software makes it easier to read, track, and record your stator test information. While performing tests, you can watch the testing throughout the process in real time. You can view various wave-forms for surge or magnetic field, which can be displayed real-time and printed if desired. The software logs all test results, so that you do not have to worry about losing important information. ESW designs the tooling to be simple to connect the part. We work closely with you to define and implement your customized testing needs. The videos and slideshow below show some of our Stator Testers.
