Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe Power Relay Module, 8xSPDT, 5 Amp, 50-Pin SGMC Connector
40-158-004
The 40/42-158-004 is a PXI/PXIe high density power relay module with 8xSPDT switches rated at 5A. User connection is via a 50-pin SGMC male connector. The 40/42-158 range is available in 8, 16, 24 or 32 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
Plus Radio Ethernet Receiver
ACSRF-4040
The Plus Radio Ethernet receiver is required as part of the Tinytag Radio Data Logging System. It controls the transmission of data to and from the radio loggers: data received from the loggers is then sent to the computer for viewing with Tinytag Explorer radio software. If power to the computer running the system is lost, the receiver has a battery back-up which will maintain the mesh network until power is restored. This receiver plugs directly into a LAN removing the need for a computer in the area where monitoring is to take place. The receiver is powered using a plug-in Power over Ethernet adaptor (ACS-0041) which is supplied with the unit.
-
product
PoE Voltage Monitor Detect & Verify
PE-400
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
product
Ultra-Compact Embedded Computer for Mobile Use (Transport, Surveillance, Industrial)
Neousys POC
Ultra-compact embedded computers based on Atom ™ processors for mobile use (transport, surveillance, industrial).- Ultra-compact industrial computers- Intel® Atom ™ E3845 1.91GHz Quad-core (POC-200), Intel® Apollo Lake Pentium® N4200 and Atom ™ E3950 quad-core (POC-3xx) processors - Operating range from -25 ° C to 70 ° C based on fanless cooling- Gigabit PoE and IEEE 802.3at PoE + ports- USB 3.1 Gen1 and USB 2.0 ports - RS-232/422/485 ports
-
product
802.11n wireless access point
SX-AP-4800AN2
SX-AP-4800AN2 is a dual band 802.11n wireless access point (base station) and is able to communicate with station devices (clients) supporting IEEE802.11a/b/g/n wireless networks. SX-AP-4800AN2 is ideal for business and factory environments supporting enterprise wireless security and PoE (Power over Ethernet).
-
product
High Speed Industrial GigE Cameras, 5g and 10g Models
LUCID Atlas
Industrial GigE (5GigE and 10GigE) cameras;IP67 models available!There are SWIR models !Ethernet Cat 6.a up to 100 m;Power supply: PoE;Resolution from 2.8 to 31.5 MP;High speed of data transfer;Price: from $ 1,250.00.
-
product
Industrial ATX Motherboard With 12/13/14th Gen Intel® Core™ I9/i7/i5/i3 Processor
IMB-M47
ADLINK's IMB-M47 ATX Motherboard is a driving force behind industrial automation, supporting 14/13/12th Gen Intel® Core™ processors, and delivering substantial improvements in performance, capacity, and GPU support through its seven PCIe slots, PCIe 5.0 compatibility, DDR5 memory, and 2.5GbE PoE capability. Tailored for a range of industrial applications including automation, machine vision, factory automation, and logistics, the IMB-M47 features up to 128GB DDR5 memory at 4800MHz, supports three independent displays, offers USB 3.2 Gen2x2 (20Gb/s), 3x 2.5GbE LAN, multi-M.2 Key M, TPM 2.0 security, and PCIe 5.0 slots for high-performance add-on cards. Optimized for the latest Intel processors, this motherboard blends efficiency and performance cores, bolstering edge applications with swift memory performance via DDR5 technology. With a commitment to technology leadership, ADLINK equips customers with the tools to harness the latest processors, streamline real-time graphics processing, and fuel innovation in Edge AI applications, solidifying its role in the future of industrial edge computing.
-
product
PC/104 Single Board Computer with Vortex86DX3 System-on-Chip
CM1-86DX3
The CoreModule CM1-86DX3 is a PC/104 board with DMP Vortex86-DX3 single chip solution and has a very good performance to power ratio. The board comprises all peripherals needed for an embedded PC on a small 3.775" by 4.050" printed circuit board. The CM1-86DX3 integrates a powerful yet efficient DMP Vortex86DX3 with graphic controller and audio controller together with an additional GBit Ethernet controller to form a complete PC, with all the standard peripherals already onboard. Two Ethernet ports (1x GBit and 1x 100MBit), four RS232/RS422/RS485 serial ports, two USB 2.0 host controller to handle the communication with external devices. There are PS/2 connectors for keyboard and mouse. A first generation SATA interface allows the connection of hard disk or CD drive. CFast is also available. System expansion can easily be realized over the PC/104 bus connectors.
-
product
Thermometer with PoE
T4611
PoE Web Sensor for external Pt1000 temperature probe. Power over Ethernet feature according IEEE 802.3af is supported.
-
product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
PSL-3424 Quick Test for 802.at and 802.3bt PSE's
*Accessible from PSA Interactive or PowerShell PSA*Scans 2 to 8 PSE ports per test cycle*Automatically determines and adapts to PSE maximum assigned class*Tests PSE’s that grant full power via PD Classification or through PoE LLDP*Validates PoE Detection Acceptance and Rejection Range*Measures PSE Port Voltage at both minimum (DC MPS) and maximum (Pclass) load conditions*Reports PSE type (AT vs BT), maximum assigned class capability, and Pclass power capacity*Assesses Disconnect Power Removal response*Assesses Overload Power Removal response*Assesses LLDP Power Protocol and Allocations (PSL-3424L)
-
product
Network Communication Platform Peripheral
Axiomtek provides different add-on cards for network appliance, such as PCIe PoE cards, network security cards, IPMI and more.
-
product
Short-Wave Infrared Camera
Goldeye G-032
The Goldeye G-032 SWIR camera supports Power over Ethernet (PoE) and data transmission with up to 100 m distance. Thanks to the integrated image optimization, the Goldeye is distinguished by an excellent image quality.The fanless model is optimized especially for industrial applications. It enables an easy system integration thanks to various mounting options, screw locks, extensive I/O control as well as many machine vision features.
-
product
Web Sensor with PoE
T3611
Ambient temperature, relative humidity t-line Web sensor with Power over Ethernet feature. Remote alarm.
-
product
Vision System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron®, Intel® Q170, 4 PoE, 4 USB 3.0, And Real-time Vision I/O
IPS962-512-PoE
The IPC962-512-PoE meets the increasing requirements for maximum quality and flexibility in modern production plants. It features flexible expansion capacity, camera communication interfaces, real-time vision-specific I/O with microsecond-scale and LED lighting control. This machine vision controller is powered by the LGA1151 socket 7th/6th generation Intel® Core™ (codename: Kaby Lake/Skylake) and Celeron® processors (up to 65W) with the Intel® Q170 chipset. The IPS962-512-PoE comes with a full range of isolated I/O interfaces and real-time controls essential to machine vision applications, including trigger input, LED lighting controller, camera trigger, as well as an encoder input for conveyor tracking. The real-time vision system PS962-512-PoE enables a fast and high accurate inspection to ensure that the desired quality is achieved with no manufacturing defects. It supports four IEEE802.3at PoE LAN ports and four USB 3.0 ports for connection with industrial cameras. Operating over a wide temperature range from -10°C to +55°C, the IPS962-512-PoE provides reliable and stable performance within severe environments. Its easy setup and compact design are ideal for space constrained environments. Moreover, one PCIe x16 and one PCIe x4 expansion slots allow quick installation of I/O cards and graphics cards. Two easy-swappable 2.5" HDDs are available for extensive storage needs.
-
product
Dual PoE-PSE I/O Board/Box
AX93A21
*2 PoE-PSE ports comply with IEEE802.3af standard via an internal cable or network cable connected to LAN ports on SBC to power an external PoE device*With an external 12 VDC-in, the 2 PoE-PSE ports are capable of following IEEE802.3at standard
-
product
Power Over Ethernet (PoE)
Power over Ethernet (PoE) is a revolutionary technology that enables delivery of power over standard Ethernet infrastructure to facilitate quick and easy installation of WLAN access points, network cameras, IP telephones and other IP-based devices. The proliferation of Ethernet-connected devices such as Pan-Tilt-Zoom (PTZ) security cameras, 802.11ac and 802.11ax access points, LED luminaires and Internet of Things (IoT) appliances has created an unprecedented demand for more power. PoE is the key to efficiently, cost-effectively and reliably power network devices.
-
product
LLDP Emulation And Analysis
802.3at and 802.3bt PD Emulation and Protocol Analysis
*Integrated PoE LLDP and Load Emulation in a Single Instrument*IEEE 802.3at and 802.3bt LLDP Compliance Analysis*Independent, Per-Port 802.3at and 802.3bt LLDP Emulations*Flexible Single and Dual Signature PD LLDP Emulations*One-Click LLDP Protocol Capture and Analysis*Pop-Up Excel Spreadsheet Reports Assess Protocol Content and Timing*Enables One-Click Emulated Power-Ups and Standard Waveforms with LLDP Power Granting PSE's*Enables 2-Pair and 4-Pair PSE Conformance Test Suties with LLDP Capable PSE's*Enables 2-Pair Multi-Port Suite with LLDP Capable PSE's*Available for PSA-3000 and PSL-3000 Platforms
-
product
PoE Tester
PE-100
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotation between voltage (Volts), current(Amps) and power(Watts) via dual 4 digit 7 segment LEDs which provides voltage available, current flowing and how much power an PD actually need ensure sufficient power for PD to make the PoE is sustainable.
-
product
Power over Ethernet (PoE) DC/DC
An isolated 25W, PC/104-Plus form factor, 802.3af/at compliant, PoE PD power supply. The Class 4 signature supports up to twice the power of 802.3af compliant PD devices. Designed to power a single board computer from DC power extracted from a CAT5 cable sourced by an 802.3af/at compliant PSE device configured as either an endpoint or midspan device.
-
product
PoE Module
PoE-PSE I/O boards comply with IEEE802.3af standard via an internal cable connected to LAN port on a SBC to power an external PoE device
-
product
Network AutoTester
LinkRunner® AT
Test and validate copper and fiber Ethernet connectivity in less than 10 seconds. Validate up to 30W 802.3af/at PSE with TruePower™ loaded Power over Ethernet (PoE) test. Verify twisted-pair cable length and wire-map in a snap.
-
product
Pocket Network Tester
LinkSprinter®
The LinkSprinter Pocket Network Tester verifies the functionality of copper Ethernet links and identifies errors in less than 10 seconds. The tester reveals network connectivity status and port information while ensuring documentation for every link. The comprehensive AutoTester measures PoE voltage, performs a switch test, and confirms the DHCP server is running and responsive. The tester also verifies gateway/router, internal IP service, and cloud reachability. When paired with the secure Link-Live Cloud Service, the Network Tester automatically uploads results and allows annotation of results enabling job supervisors to easily manage the progress of deployment and troubleshooting tasks assigned to their team.
-
product
2/4-CH PCI Express® GigE Vision PoE+ Frame Grabbers
PCIe-GIE7x Series
- Hardware Trigger over Ethernet with Action Command- Up to 120W PoE power from PCIe bus/4-pin/6-pin Molex connector- PCI Express® x4 compliant- IEEE 802.3at for PoE+ (Power over Ethernet Plus)- PoE protection and automated power budget control for enhanced asset protection- Easy-to-use utility and API provided for PoE power management- Multiple cards, multiple cameras, in a single system- Wide operating temperature range from 0°C to +70°C supporting non-drop frame capture in extreme environments
-
product
Web Sensor with PoE
T3611-2
Ambient temperature, relative humidity t-line Web sensor with Power over Ethernet feature. Remote alarm.
-
product
4CH GigE Vision Compact Vision System with 6th Generation Intel® Core™ i7/i5/i3 Processors
EOS-1300
ADLINK’s EOS-1300 is a high performance compact vision system equipped with 6th Generation IntelR Core? i7/i5/i3 processors and four independent PoE (power over Ethernet) ports, delivering data transfer rates up to 4.0 Gb/s. EOS-1300’s FPGA based DI/O provides programmable de-bounce filter, on the fly trigger, and user wiring Sink/Source DO and Encoder functions, making it the ideal solution for machine vision applications requiring high computing power and time deterministic solutions with minimal footprint.
-
product
Value-added Module With 4 M12 X-coded GbE LAN And PoE
VAM706/VAM707
*4 x M12 X-coded GbE LAN or PoE/PoE+*Swappable modular design*Maximize I/O flexibility*Designed for tBOX300/500 series*CE, LVD, FCC and EN 50155 compliant
-
product
Robust DIN-rail Fanless Embedded System With Intel® Celeron® Processor N3060/N3160, 2 COM, 4 USB, 2 GbE LAN (1 PoE PD), DIO And RTC
ICO310
The ICO310, a robust din-rail IIoT (Industrial IoT) embedded platform, supports low power Braswell Intel® Celeron® processor N3060 1.6 GHz dual-core or N3160 1.6 GHz quad-core with up to 8GB DDR3L system memory, delivering high performance and low power consumption at competitive price. The outstanding Braswell Intel® Celeron® SoC-based embedded field controller offers complete expandability and full featured I/O, including two Gigabit LAN ports, two RS-232/422/485 ports, two USB 2.0 ports, two USB 3.0 ports, one VGA port, and one DIO interface. Two PCI Express Mini Card slots, one SIM card slot and three internal antennas are available for 3G/GPRS and Wi-Fi connections. Furthermore, the ICO310 features PoE PD function, which can simplify network installation and minimize the total costs of replacement and maintenance. Its storage interfaces include an SATA SDD, as well as mSATA support on the PCI Express Mini Card slot. Additionally, the wide range 12V-24V DC terminal block power input with overvoltage and reverse protection can lower the risk of data loss under human manipulation. The reliable yet robust ICO310 is a perfect solution for industrial IoT applications such as smart energy, smart factory automation, facility monitoring systems and many more.
-
product
Gigabit (PoE), 2 Port, Network Interface Card
Ethernet Network Interface Card
Gigabit (PoE), 2 Port, Network Interface Card
-
product
Broadband Power Amplifier
PAS-00210-60
* Solid State Power Amplifier* Gain : 50 dB typ.* High IP3, 51.0 dBm typ.* Rack Mount Case* Internal Cooling Fans* Over Temperature Protection* Output VSWR protection* Microprocessor controlled* Front Panel Information Display* RS-232 Interface* Ethernet Interface* Variable Gain* ALC power control* Type N Connectors
-
product
Ethernet POE & PHY Testing
Networked Communication Solutions, LLC
A multi-port programmable load.
-
product
PSE Test Solutions
Explore Power Over Ethernet (PoE) PSE Test solutions from Sifos Technology. What type of testing does your PSE need?
