Filter Results By:
Products
Applications
Manufacturers
Parallel Digital I/O
Processes multiple bits or data paths simultaneously.
- Pickering Interfaces Inc.
product
PXI H. Density Digital I/O Module 32 Bit O/C
40-410-002
The 40-410 range of Digital I/O Modules are suitable for operating external devices, such as heavy duty relays (power, RF and high voltage types), solenoids, lamps, or for interfacing with external logic such as a programmable instrument with a BCD interface. Two choices of output drive are available: TTL for interacting with external logic and Open Collector Transistor for operating external devices with voltages to 50VDC and currents to 500mA.
-
product
100 MHz 32-CH High-Speed Digital I/O Card
PCIe-7360
ADLINK's PCIe-7360 is a high-speed digital I/O board with 32-CH bi-directional parallel I/O lines. Data rate up to 400 MB/s is available through the x4 PCI Express® interface. Clock rate can support up to 100 MHz internal clock or 200 MHz external clock, ideally suiting applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
product
PXI 32 Channel I/O Serial I/P Prog Threshold
40-412-001
The 40-412 is a 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels
-
product
PCI 24-Bit Digital I/O Cards
PCI-DIO-24D/H
These cards are 24-bit parallel, digital input/output cards designed for use in PCI-Bus computers. The difference between the models is that I/O connections to PCI-DIO24D are via a standard 37-pin D-sub connector while I/O connections to PCI-DIO24H are via a 50-pin connector. The cards are 4.80 inches long (122 mm) and may be installed in any 5V PCI-bus slot in IBM and compatible personal computers.
-
product
I²C/SPI Interface Device
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
product
PXI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module
778543-01
48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module—The PXI‑6528 is an industrial, parallel digital I/O interface. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
PCI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, Digital I/O Device
778833-01
The PCI-6528 is an industrial, parallel digital I/O interface.With programmable power-up states, you can configure the initial output states in software, to ensure safe … operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
IP-Parallel-BA1 "IP-Tape"
The IndustryPack compatible IP-Tape design adds 48 digital parallel IO lines to one slot of your carrier board. The IO is dedicated to a DTC interface. Other interfaces can be implemented. The DTC interface has 22 Address, 16 Data plus Parity, 4 control and 5 status lines. Parity is automatically generated in write mode and checked in read mode.
-
product
Multi-Wafer Test & Burn-in System
FOX-XP
The key features of the new FOX-XP test cell that contribute to the cost-effectiveness of the solution include the ability to provide up to 2,048 "Universal Channels" per wafer, which allows the system to test all the devices on the wafer in parallel. The new "Universal Channel" architecture allows any channel to be any function (I/O, Device Power Supply (DPS) or Per-pin Precision Measurement Unit (PPMU)). This enhanced architecture now allows customers to perform per pin parametric testing, more extensive digital pattern test with deeper data stimulus / capture memory (32M per pin), and deeper scan (768M) optimized for BIST/DFT testing.
-
product
50 MHz 32-CH High-Speed Digital I/O Card
PCIe-7350
ADLINK's PCIe-7350 is the advanced version of hot-selling PCI/PCIe-7300A featuring high-speed digital I/O with 32-channel bi-direction parallel I/O lines. The data rate can achieve up to 200 MB/s through the x1 PCI ExpressR interface. The clock rate can support up to 50 MHz internal clock or 100 MHz external clock, which is ideal for the applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
product
Non-Isolated Digital I/O DAQ Cards
PCI/PCIe-bus non-isolated digital I/O cards for parallel data transfer, TTL DIO, and logic signal sensing.
-
product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
product
PXI-6529, 48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module
779949-01
48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module—The PXI‑6529 is an industrial, parallel digital input interface. PXI‑6529 devices are ideal for a variety of applications from automotive design, industrial factory automation, and machine control to aerospace, laboratory research, and biomedical applications. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6529 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Digital I/O Board w/CoS IRQ
104-DIO-48S
*48 or 24 parallel lines of 82C55 digital I/O with tristate buffers prevent unintended control of external equipment*IRQ on input change of state (COS) eliminates the need for constant polling*High sink/source current 64mA/32mA*I/O pulled up to 5V for contact monitoring*Compatible with Opto-22 and other industry standard I/O racks
-
product
Ethernet To Parallel Digital Interface Boards
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-101
A 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels.
-
product
Non-isolated Digital I/O ISA DAQ Cards
PCI-bus non-isolated digital I/O cards for parallel data transfer, TTL DIO, DTL and CMOS DIO logic signal sensing.
-
product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-111
A 32-channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low usinga high current capacity drive capable of sourcing 0.4A from the high side or 0.5Asink on the low side for each channel. The module is available in two versions witheither serial or parallel capture of the input levels.
-
product
IP Parallel IO
IndustryPack compatible IP-Parallel-IO with counter and timer design adds up to 48 digital parallel IO lines to one IP slot of your carrier board.
-
product
224 Channel Digital I/O Modular PXI Card
GX5731
The GX5731 is a 6U modular digital I/O card with 224 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5731 offers the highest density in the industry for a single PXI plug-in board. Of the 224 channels, 128 support TTL levels with the direction of each group of eight channels programmable as input or output. The other 96 channels can be used for customized I/O using MTS' GX57xx series I/O modules.
-
product
32-CH 80 MB/s High-Speed Digital I/O Card
PCIe-7300A
ADLINK PCIe-7300A is an ultra-high-speed digital I/O card. It consists of 32 digital input/output channels. High performance designs and state-of-the-art technology make this card ideal for a wide range of applications, such as high-speed data transfer, digital pattern generation and digital pattern capture applications, and logic analyzer applications. Trigger signals are available to start the data acquisition of pattern generation.
-
product
PCIe-7821, Kintex 7 FPGA, Digital Reconfigurable I/O Device
785359-01
The PCIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PCIe‑7821 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in-‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
product
Dynamic Digital I/O (3U), 32 Channel, 50 MHz
GX5291-50
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 32 ch. up to 50 MHz w/128MB On-Board Memory, 32-ch Domain.
-
product
Industry Pack Carriers and Digital I/O
CPCI-4SIP-6U
The CPCI-4SIP-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4SIP-6U is the perfect solution. There are four (4) Industry Pack sites providing up to 200 I/O pins accessible from either the front panel or the rear back plane.
-
product
Digital Source Capture Unit
DIO2
The DIO-II module is a multimode digital source and capture unit. In Low Speed Mode it provides a 20-bit parallel or 24-bit serial I/O capability running at speeds up to 50 MHz. In High Speed Mode, the DIO-II provides a 16-bit parallel I/O capability up to 200 MHz. In both Modes, the Clock is generated by a low jitter PLL source that is capable of generating clocks from 320 kHz up to 1 GHz.
-
product
PXI Opto-Iso Digital I/O 32bit out 16bit in
40-490-002
The 40-490 Digital I/O Modules are designed for applications requiring optically isolated digital I/O, typically in industrial automation. This modules features 32 digital outputs and 16 digital inputs which may be programmed by word or individual bit. Power for the isolated section of the module is built onto the board in model 40-490-001, or this can be supplied externally in model 40-490-002.
-
product
PXI 32 Channel I/O, High Side Driver
40-413-001
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
product
Keysight 64-bit Digital I/O with Memory and Counter for 34980A
34950A
The Keysight 34950A module for the 34980A Multifunction Switch/Measure Unit has 64 bi-directional lines configured as eight 8-bit channels. Each 8-bit channel has programmable polarity and thresholds up to 5V. The memory is useful for simulating and capturing digital patterns up to 10 MHz. It provides configurable handshaking protocols for a wide variety of applications.
-
product
6U PXI Multi-Channel Analog I/O PXI Card
GX3348 Series
The GX3348 is a multi-channel analog I/O 6U PXI card which provides (3) programmable sources, a ground source connection, a pulse / square wave generator (A version only) and a 4 x 48 or 4 x 64 matrix - allowing the user to route the 3 sources, or ground to any of the 48 or 64 I/O channels. In addition, each I/O channel can be connected to a 16-bit A to D converter, providing DC voltage measurement capability for each channel. The module also offers (8) static digital I/O for controlling / monitoring a UUT's digital signals.
-
product
48 Optocoupled Open Drain 42V 6A Digital Outputs
YAV90048
6×8 Isolated Ouput Banks Trigger IN and OUT Termic and Overcurrent protection CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
