Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Diagnostic Test Tool
BIRST™ (Built-In Relay Self-Test)
Verification and diagnosis of complex switching operation in a test system has always been an issue. BIRST (Built-In-Relay-Self-Test) diagnostic test tool provides a quick and simple way of finding relay failures available on some of our LXI and PXI switch matrices.
-
product
50 Channel Linear Vibration Motor Aging Unit
BK2021
The BK2021 50 Channel Linear Vibration Motor Aging Test System was designed to test your linear vibration motors so you know they are working. Load a jig drawer in the jig assembly unit with 10 DUT's. Close the drawer to start testing and begin loading the next of the 5 drawers. When the machine has finished running up to 4 test sequences that you've programmed in, the drawer opens. On the front, a green light tells you the motor is good, a red light tells you there was a short and if there is no light you know there was an open circuit.
-
product
Rail Traction Inverter Test System
The rail inverter test system uses a pulse test methodology to verify proper operation of the IGBT switching elements in a subway car motor control. The system is designed to verify proper commutation of the switching elements. A large capacitor bank allows testing at DC voltages up to 1kV and peak currents of up to 3kA into reactive loads.The system also integrates self test capabilities and safe-to-turn-on (STTO) diagnostics to ensure no gross faults are present prior to the application of high voltages. Further the system includes dielectric withstand (hi-pot) test capability to ensure electrical safety.
-
product
DC Vibration Unit Tester
BK2116
As the technology for BLDC motors advances, more advanced testing is also needed. The BK2116 DC Vibration Motor Tester was designed when of several of our clients needed to test the new generation of 3 port DC vibration motors. Using the BK2116, you can test the electrical specifications (RPM, current, drop pulse, and start up voltage) and also vibration level, and noise of motors with either 2 or 3 ports. The BK2116 can concurrently test 2 DUT's and BaKo's Test Shop software makes it very easy to set up and test. And because you use it with a PC or notebook, you can see graphs of the data as you test, and also save it to analyze later, or to analyze the data you gather over time.
-
product
Spring Fatigue Testing Machine
TPJ Series
Jinan Testing Equipment IE Corporation
Model TPJ Series Mechanical Computer Control Spring Fatigue Testing Machine is mainly used for the fatigue properties of all kinds of coil springs, disc springs, shock absorbers, and seal springs etc. The Spring Fatigue Testing Machine consists of motor, reducer on the connecting cams to drive the connecting rod and make reciprocating motion achieve the compression fatigue movement. The Spring Fatigue Testing Machine is efficient without any pollution to the environment. Equipped with different accessories, the Spring Fatigue Testing Machine can test springs of different sizes. Adopting the single-chip machine control, the Spring Fatigue Testing Machine realizes auto stop function when it reaches the preset test times. The Spring Fatigue Testing System is widely used in quality controls for spring, shock absorber production, and relevant applications.
-
product
Wound Component EST Analyzer
19036
Chroma Systems Solutions, Inc.
The industry’s first Wound Component Electrical Safety Test (EST) Analyzer that combines impulse winding, AC/DC hipot, insulation resistance and DC resistance test measurement functions. Chroma’s 19036 Wound Component EST Analyzer has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement with a maximum output of up to 40 channels. Capable of outputting and measuring AC100mA/DC 20mA, Chroma’s 19036 is suitable for testing to high power motor standards such as UL 1004-1.
-
product
Motor Stator Test System
Chroma 1920
Chroma Systems Solutions, Inc.
For electrical safety and quality testing functions of motor stator coils
-
product
Automotive EMC test systems
Dozens of manufacturer's and other automotive immunity standards with their roots in ISO 7637 continue to evolve bringing new challenges to users of conducted immunity testing. Teseq continues to advance the state of the art, bringing simple, flexible solutions for the challenging and fast-changing requirements that are 42 V ready.Teseq has been at the forefront of the pioneering work to establish EMC tests for motor vehicle electronics. Automotive manufacturers and suppliers worldwide have come to trust test systems from Teseq. Active involvement in the standardization committees ensures that the latest advances are continously reflected in our test systems.
-
product
Three-Phase Transformer Winding Resistance Meters
TWA Advanced Series
TWA Advanced series is the latest DV Power solution for three-phase transformer winding resistance measurement and tap changer analysis. They are capable of testing six transformer windings with a single cable connection, as well as three-phase automatic transformer demagnetization. It has the option of the automated test mode, where the instrument operates the tap changer without operator input (minimizing the risk of human error) and records winding resistance results based on pre-selected stabilization criteria.The unique DVtest method of tap changer analysis enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, together with the measurement of tap changer motor current which detects motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or simultaneously on three phases. It can also be performed together with the winding resistance test in all tap positions.A unique advantage of TWA Advanced instruments is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer connected in a YN configuration. This can significantly speed up the testing– for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.TWA500 is equipped with a large 10.1” graphical touch-screen display, while TWA400 has a 7” graphical touch-screen display. Besides making the interface much more user-friendly compared to older winding ohmmeters, it also enables certain test options that were previously available only with DV-Win software. The most important among them are DVtest, tap changer motor current measurement, “Heat Run” test, test templates, and automatic test mode.
-
product
Tensile Strength Tester
Capacity of Tester with accuracy of 100g : 250 Kgf. and 500 Kgf.Capacity of Tester with accuracy of 10g : 20 Kgf, 50 Kgf and 100 KgfS Type Load Cell fixed with Top GripTraverse Speed: 300 & 100mm /min.Grip Separation: 1000 mmGrip Separation: 25 mmTop Grip is fixed and Bottom Grip is Movable Type.Elongation measurement by Steel Scale and Digital Counter Meter Both.Digital Display of Load and Elongation.Peak value of last test can be read.User friendly key panel with switch of zero setting and peak value of last testMotor: 1/2 HP single phase 220V 50 Hz. ( for Capacity up to 100 Kgf )Motor: 1 HP single phase 220 V 50 Hz ( for Capacity up to 500 Kgf)Power: 220 V AC 50 Hz.Safety device by limit switch to protect from over traverse.
-
product
Motor Test Instruments
The absorbed energy of the DCE series Dyno is converted into heat in two rotors located at the external side of the coils . The rotors are designed with curvilinear cooling fins for fast dissipating heat into the atmosphere . This design provides with the smallest physical size for air cooled Eddy-Current Dyno . Simple construction and desirable speed-torque characteristics are adaptable to most of the applications.
-
product
High Voltage Tester
Aarohi Embedded Systems Pvt. Ltd
AAROHI make high voltage tester is specially designed to test induction & submersible motors with cutting edge technology.High Voltage Tester is manufactured as per the International set standards and regulations. This High Voltage Testers are available in AC and DC types and are used for testing HV cables after installation and repair for ensuring efficient performance. It also indicates voltage withstands level and current leakage level of the cable during the testing period.
-
product
Drop Tester
KD 688 A
King Design Industrial Co., Ltd.
*PLC control, linear motor fast speed control the height setting.*Alarm warning before testing.*Light support structure decreases the test impact.*Support dropping very smooth with dual lubrication guide.*No second impact. *A data acquisition for the impact wave record (Option).*Non maintenance request for continue operation.*According to ISTA, ASTM .....etc international standard.*Equipped edge & corner holder.
-
product
Analog Tensile Testing Machine
It can test materials like rubber, wood, plastic, rexins, teflon, cardboard, composites, ferrous metals, non-ferrous metals etc.Wide range of Grips, Attachments & Special fixtures are available to suit varieties of material and shapes. Continuous roll autographic Load Vs Elongation recorder.Continuous roll autographic Load Vs Elongation recorder.Elongation scale with least count 1 mm.Elongation scale with least count 1 mm.Three measuring ranges for accurate testing.Three measuring ranges for accurate testing.A number of straining speeds are available for proper selection.A number of straining speeds are available for proper selection. Machine with AC or DC drive motor is available.Machine with AC or DC drive motor is available.Various Models – Maximum Capacity from 200 N to 50 kN.Various Models – Maximum Capacity from 200 N to 50 kN.Loading accuracy well within ±1%Loading accuracy well within ±1%Hand operated cutting press with different sizes dies are available for cutting dumbbell specimen.Hand operated cutting press with different sizes dies are available for cutting dumbbell specimen.
-
product
Testing Aerospace Motors
Magtrol designed this Custom Motor Test System for the testing of various aerospace motors for both commercial and military applications.
-
product
Electric Servomotor Packaged Cargo Compression Tester
It is a testing device that can perform compression evaluation test of packaged cargo equipped with an electric servo motor type actuator.
-
product
Axle Damping Test Bench
C_MSD S 13.0 W220 | VP 215051
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
product
High Gain Horn Antenna
BBHA 9120 K
The BBHA 9120 K is a linear polarized high gain horn antenna for immunity testing at short distances, especially optimized forAutomotive 600 V/m Pulse Radar Test 1.2 - 1.4 GHz. Standard: General Motors: GMW3097, Ford: EMC-CS-2009.
-
product
Axle Damping Test Bench
C_MSD C 13.0 W220 | VP 215050
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
product
Motor Tester and Analyzer
ITIG
The iTIG III is the industry’s most advanced electric motor tester and winding analyzer. Bringing confidence to motor repair companies, industrial end users, OEMs, and manufacturers of rotating equipment, the iTIG III features over 20 high- and low-voltage tests including high frequency surge and partial discharge.Choose multiple tests to run automatically in a sequence or select single tests. Report results with the easiest to use instrument available. Manually operate voltage dial or set up for automatic operation. Carry the iTIG III in the field or use it as a benchtop device. Connect to an external portable power pack for testing up to 40kV. The iTIG III is the most versatile and easy-to-use tester available.
-
product
3-in-1 Test System
CIBANO 500
CIBANO 500 combines a micro-ohmmeter, timing analyzer, and a coil and motor supply. All important CB tests on all types of CBs can be carried out even when a station battery is not available.
-
product
Aniline Test Equipment
Labodam aniline test equipment are designed with stepless speed regulation motors to have a smoother operation and automatic alarm system with sound and light to detect end point.
-
product
Motor-Type Tester
QME-2A
Changzhou Chanlon Electronic Technology Co., Ltd.
This tester is applied to type test of every kinds of single phase, three phases AC and DC motor. Its LCD shows all technical data which obtained by industrial control computer, printed out by printer in graphic and report (test items difference appear in the different types motor).
-
product
Custom Automation Equipment And Assembly Machinery
Automated test equipment, precision positioning robots, stepper motor, and servo motor mechanisms in support of testing and repetitive manufacturing from TetraTek Products, Inc.
-
product
Power Cord Bending Tester
SW-6
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
product
Motor Stator Tester
DZ901
Shanghai Aoboor Electric Co., Ltd.
Applicable to precision electrical properties test of stators of y-type three-ohase motors, single-phase motors, hub generators, brushless motors and servo motors.
-
product
Microohmmeter
MMR-6500
The MMR-6500 digital meter is designed for measuring low resistances with a stabilised current of up to 100 A. The use of test clamps enables the safe measurement of breakers (high-, medium- and lowvoltage), isolators and other components earthed on both sides. The MMR-6500 series meters are equipped with a unique module in their class that measures inductive components which have a current of up to 10 A, enabling the winding resistance of motors, transformers and other inductive components to be measured. Another useful function is the temperature measurement and the automatic compensation of results with relation to the measured temperature or temperature set by the user. The system is completed with a recorder function. Special measuring algorithms and additional functions allow an appropriate measuring method to be chosen depending on the measured component and measurement conditions, thus, widening the application areas of the meter. The state-of-the-art user interface, various communication interfaces, wireless communication and communication with the computer, printer, 2D code reader are integrals features which enable full, comfortable and intuitive management of not only measurements and their results but also ID data of measured components.
-
product
NI-9244, 400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module
783106-01
400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module - The NI‑9244 performs single-ended analog input. The wide measurement range makes it ideal for high-voltage measurement applications such as phasor measurements, power metering, power quality monitoring, industrial machinery, and motor test. You can also perform transient and harmonic analysis with high-speed simultaneous sampling. The NI‑9244 offers three channels, so you can connect single‑ or three‑phase measurement configurations such as WYE and delta. You can incorporate the NI‑9244 into systems to meet standards such as IEC 61010‑1, C37.90 and C37.60, IEC 60255‑22‑(1:7), IEC 60255‑1, C37.188 Class M and P, EMC section of IEC 60870, EMC sections of IEC 61850, IEC 61000‑4‑30 Class S, and IEC 61000‑4‑7.
-
product
AC Voltage Test Systems
HIGHVOLT Prüftechnik Dresden GmbH
AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
product
Heavy Duty Dynamometers
Designed to be a performance dynamometer first, with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD.
-
product
Compression Test Apparatus
CT-20 C
Is designed to perform tests specified in many standards where resistance of insulating materials to elevated operating temperatures is to be determined. It is used to test insulation materials used in Electrical Appliances, Electrical wiring accessories, luminaires, motors, connectors, etc. The test ensures that external parts of insulating material, the deterioration of which might cause the appliance to fail to comply with the relevant standards, are sufficiently resistant to heat
