Filter Results By:
Products
Applications
Manufacturers
Mechanical Test
material and physical properties.
- Pickering Interfaces Inc.
product
PXI High Density MUX BRIC, 24-Chan, 20-Pole
40-570-313
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
High Speed DAQ Card
With 25 MS/s, 100 MS/s or 250 MS/s the high speed input cards are suitable for the acquisition of ultra fast, accurate and high resolution transient signals in high speed mechanical tests or electrical/electronic environments. 14-/15-/16-bit resolution; dynamic resolution increase. available 5/18
-
product
CMP Mechanical Kits (230x135mm)
230199 – CMP-240-HP
The CMP Mechanical kits are an excellent option for manual tests of both low and high volumes. Now in a more rigid design with removable probe plate for easier maintenance. Integrated fixture down switch as an option. The kit is available in 4 standard sizes but can be adjusted to your demands.
-
product
PXIe-2542, 6.6 GHz, 50 Ω, Solid-State, Quad 2x1 PXI RF Relay Module
780587-42
PXIe, 6.6 GHz, 50 Ω, Solid-State, Quad 2x1 PXI RF Relay Module - The PXIe‑2542 is a terminated switch module suited for routing RF signals for production test applications. It features high-performance solid-state relays that offer unique benefits such as unlimited mechanical lifetime and fast switching time. Front-mounted SMA connectors provide easy connection to your RF devices, and the module features termination on every COM line and channel. The channel termination and COM lines help minimize reflections of the RF signal and protect your instruments.
-
product
Spring Fatigue Testing Machine
TPJ Series
Jinan Testing Equipment IE Corporation
Model TPJ Series Mechanical Computer Control Spring Fatigue Testing Machine is mainly used for the fatigue properties of all kinds of coil springs, disc springs, shock absorbers, and seal springs etc. The Spring Fatigue Testing Machine consists of motor, reducer on the connecting cams to drive the connecting rod and make reciprocating motion achieve the compression fatigue movement. The Spring Fatigue Testing Machine is efficient without any pollution to the environment. Equipped with different accessories, the Spring Fatigue Testing Machine can test springs of different sizes. Adopting the single-chip machine control, the Spring Fatigue Testing Machine realizes auto stop function when it reaches the preset test times. The Spring Fatigue Testing System is widely used in quality controls for spring, shock absorber production, and relevant applications.
-
product
RMC-8355, 2.4 GHz, 1U Rugged Rack-Mount External Controller for PXI
782568-01
2.4 GHz, 1U Rugged Rack-Mount External Controller for PXI - The RMC‑8355 is a rugged 1U rack-mount controller for PXI- or PXI Express-based systems intended for test and measurement applications requiring rack-mount controllers. It features up to two Intel Xeon E5620 quad‐core processors that support up to 96 GB of DDR3 RDIMM ECC RAM. The RMC‑8355 offers hot-swappable fans, options for redundant power supplies, and support for RAID arrays, which allows multiple hard drives to be configured for high performance for mission‐critical, physically demanding applications. The RMC‑8355 meets the PXI standard’s mechanical shock and vibration specifications and functions over wide operating ranges.
-
product
High Performance Chipscale Test Sockets
SC
Ardent Concepts Test Sockets for ATE test deploy patented SC Contact Sets. This technology is capable of over 2 Million mechanical insertions in production environments and uses easy to replace pins with no complicated assembly procedure. It is designed to be drop-in compatible with 1mm offset and straight through footprints to ease implementation, and RC SC’s simple and robust design is extremely cost effective when compared with existing “roll” type test contactors and sockets. Designed specifically for JEDEC QFN and MLF applications, SC High Performance Test Sockets are available for most handler set-ups and offer exceptional AC performance.
-
product
Powered VXS Crates
6U VXS 6021
The WIENER VXS 6023 crate series adds high performance Switch Fabrics according to VITA 41 specification to VME based systems. Designed primarily for high speed applications in data acquisition, as well as military / aerospace test and instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
product
MECHANICAL TEST FIXTURE KITS
TX-MT-SERIES
Test-X MT Series mechanical kits are an affordable solution to printed circuit board testing. With multiple configurations and available options, this product is sure to meet your testing needs. The MT Series features a hinged 3/8" FR4 probe plate, tooling holes for accurate drilling, and side handles for easy transportation.
-
product
CAM/TRAC Test Kits
Series 47
The VP Series 47 CAM/TRAC mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 47 provides interface compatibility using the Virginia Panel ITA G12 interface. The ITA frame is offered as an option for those wanting to provide their own ITA Interface.
-
product
Precision Mechanical Calibration Kit, DC To 26.5 GHz, 3.5 Mm
85052C
The Keysight 85052C precision mechanical calibration kit contains precision standard devices to characterize the systematic errors of Keysight network analyzers in the 3.5 mm interface. This kit also contains adapters to change the gender of the test port and a torque wrench for proper connection.
-
product
Primary Standards
Primary standards (often also referred to as mechanical dead-weight testers, pressure balances or primary pressure standards) are the most accurate reference instruments for pressure. Their functional principle is based on the physical principle of pressure = force/area. Mass pieces placed on the top of a piston-cylinder system are the source of a precisely defined force. By producing a certain (counter) pressure inside the primary standard an equilibrium is achieved: the mass pieces, including the free-running piston of the piston-cylinder system, are floating, which will lead to a very accurate pressure at the test port which measured through piston gauge technology.
-
product
CMP Mechanical Kits (120x138mm)
230197 – CMP-150-HP
The CMP Mechanical kits are an excellent option for manual tests of both low and high volumes. Now in a more rigid design with removable probe plate for easier maintenance. Integrated fixture down switch as an option. The kit is available in 4 standard sizes but can be adjusted to your demands.
-
product
PXI High Density MUX BRIC, 6-Chan, 80-Pole
40-570-113
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
Failure Analysis
A partial list of our state of the art test equipment, applicable to these testing disciplines, will include the following: Two Scanning Electron Microscopes with EDS (SEM/EDS) Three Differential Scanning Calorimeters (DSC) Three Thermogravimetric Analyzers (TGA) Three Thermo Mechanical Analyzers (TMA) One Dynamic Mechanical Analyzer (DMA) Two Real-Time Fluoroscopic X-ray Systems, including a Microfocus System One Fourier Transform Infrared Microscope (FTIR) (capable of identifying a single particle of an unknown material) Two Ion Chromatographs (IC) (capable of identifying ionic impurities in ppm)
-
product
Hi-Definition Video Inspection Station with Measuring
VIS810
Video Inspection Stations are available with?or without on-screen measurement capabilities?and offer?an excellent way to evaluate or test small works or items in?difficult to access locations.? As todays electronic and mechanical systems keep getting smaller, it becomes impossible to test or measure these products with traditional methods. For many applications, from development to production testing, video based inspection can help maintain quality control. Many of these systems are used in labs for development or used in production for testing production samples.
-
product
Small Aperture Fiber-Optic Probes
Small-aperture Fiber-optic Probes are best for testing closely-spaced LEDs. With an aperture of 1mm, and a diameter of 1.2mm/0.050 inches, they can test LEDs spaced as close as 0.050 inches on center. Small-aperture Fiber-optic Probes are available with straight or right-angle stainless-steel tips as shown below. This allows for precise customization to your mechanical constraints.
-
product
Power Transformer Testers
A power transformer tester is a device that assesses a transformer's electrical, thermal, and mechanical suitability. The purpose of a transformer test is to determine if a transformer is fit for service, and to identify any defects or faults.
-
product
Three-Phase Transformer Winding Resistance Meters
TWA Advanced Series
TWA Advanced series is the latest DV Power solution for three-phase transformer winding resistance measurement and tap changer analysis. They are capable of testing six transformer windings with a single cable connection, as well as three-phase automatic transformer demagnetization. It has the option of the automated test mode, where the instrument operates the tap changer without operator input (minimizing the risk of human error) and records winding resistance results based on pre-selected stabilization criteria.The unique DVtest method of tap changer analysis enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, together with the measurement of tap changer motor current which detects motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or simultaneously on three phases. It can also be performed together with the winding resistance test in all tap positions.A unique advantage of TWA Advanced instruments is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer connected in a YN configuration. This can significantly speed up the testing– for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.TWA500 is equipped with a large 10.1” graphical touch-screen display, while TWA400 has a 7” graphical touch-screen display. Besides making the interface much more user-friendly compared to older winding ohmmeters, it also enables certain test options that were previously available only with DV-Win software. The most important among them are DVtest, tap changer motor current measurement, “Heat Run” test, test templates, and automatic test mode.
-
product
Non-terminated SPDT Indium Phosphide Active RF Switch
Part No. InPD1012-14
Non-terminated SPDT Indium Phosphide Active RF Switch • 3mm x 3mm x 1mm package size • 100ns switching time• Monolithic solid-state switch with no mechanical wear• Test board with K-connectors can be providedDC-14GHz
-
product
PXI High Density MUX BRIC, 20-Chan, 40-Pole
40-570-215
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
Textile Tensile Testing Machine
TF001
TESTEX Testing Equipment Systems Ltd.
The Textile Tensile Testing Machine is designed to test a wide range of materials in tension, bursting, tear, elongation, constant load, elastic, thread slip, peeling and other mechanical properties.A PC-controlled machine equipped with AC servomotor and a quality ABBA ball-screw for ideal and smooth control. The machine talks directly with a PC running a data analysis software package in English or Chinese, via a high speed RS232.
-
product
WinTest® Software
WinTest® is a high-performance software package that is used to operate all TA ElectroForce mechanical test instruments. With both a flexible interface and a powerful instrument controller, WinTest allows users to choose what data they monitor in real-time while accurately recording all the necessary data for their tests.A single user interface to define acquisition settings, adjust control parameters even while a test is running, and monitor a test in real-time provides a powerful solution to your testing needs.
-
product
Mechanical Design
In support of system, test and our tooling business, our mechanical engineering team is second to none in offering innovative, yet cost effective solutions for your needs.Whether it is a scalable test fixture solution or a complex, high accuracy torque tooling solution, our team of dedicated mechanical engineers can offer the right solution, with the right level of innovation to give your solution a competitive edge.
-
product
Fiber Optic Visual Fault Finder
VFF5
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
-
product
Sauter Force Gauges
Force gauges provide a quick and reliable way to obtain a measure of force in tension and compression. DMV UK offer a comprehensive range of mechanical and digital force gauges with selectable units and peak force capture with capacities from 2 N to 100,000 N. All gauges are supplied with standard accessories, a 2 year warranty, and can be used for force testing in hand held or test stand applications.
-
product
Projectile Speed Measurement Test System
This test equipment will help manufacturers, trading standards, consumer bodies, CPSC, CPSIA laboratories and regulatory authorities to check that they meet the requirements of ASTM F963 - 08 Standard Consumer Safety Specification for Toy Safety and ISO 8124-1:2009 projectile Safety of Toys –Part 1:Safety aspects related to mechanical and physical properties. It may also be valuable for certain sports equipment and related tests.
-
product
PXI High Density MUX BRIC, 12-Chan, 40-Pole
40-570-213
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
Dynamic and Satatic Electro-Hydraulic Servo Testing Machine
PLS Series
Jinan Testing Equipment IE Corporation
PLS series dynamic and static testing machine is produced according to the dynamic servo test technology. Our design of the electro--hydraulic servo testing system is unitized, standardized and modularized, which enhance the stability and reliability of the system. The electro-hydraulic servo testing system is mainly used to test the dynamic and static mechanical performance of material parts. Equipped with corresponding accessories, the servo-hydraulic testing system can do tensile, compression, low and high cycles, crack growth tests and other mechanical tests for various kinds of materials. The Dynamic and Static Testing Machine is widely used in the fields of aviation and aerospace, ship-building and military industries.
-
product
Computer Control Torsion Testing Machine
NDW Series
Jinan Testing Equipment IE Corporation
NDW Series computerized torsion testing machine provides loading and weighing capabilities in both rotation directions which enables it to determine conveniently not only the ultimate torque of a specimen, but also how the specimen behaves under conditions of continuous or intermittent torque loading in both directions. The computerized torsion testing machine is mainly used for the torsion test of metal and non-metal materials, as well as the torsion test for parts and components. The computerized torsion torsion testing machine is an essential instrument to measure torsion properties of materials for mechanical laboratories of aviation industry, construction industry, scientific research department, universities and industrial enterprises.
-
product
Design for Test
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test point access and mechanical challenges that may affect the potential test coverage. Completing a DFT enables Test Coach to make recommendations to our customers that may be implemented on boards during the design phase which will allow for the most comprehensive coverage at time of test.
