Filter Results By:
Products
Applications
Manufacturers
Fibre Optics
Field of optic fiber application.
- Virginia Panel Corporation
product
Mini Fiber Optic, Contact, Receiver, Polymer Optic Fiber
610113170
This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113171. (May mate with other ITA contacts, as well.)
-
product
PXI Quad 2 x 2 Fibre Optic Mux LC
40-860-442
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI Single 4 Channel Fibre Optic Mux FC/APC
40-850-014
The 40-850-014 4-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
"Signal Transporter"
LTX-5525
The LTX-5525 conveys sixteen independent channels of digital information over a fibre optic link ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled 100 million times per second, multiplexed and transmitted serially over an optical fiber at two gigabits per second. The receiver acquires this digital data and de-multiplexes it to 16 separate output ports.
-
product
635nm Visible Light Source
VLS-40
The KD Optics VLS-40 is an easy to use, hand-held, visible source used for testing fibre optic cable installations. It is especially useful when testing fibre optic cables close to the terminal equipment. The unit is pocket sized with a long battery life, making it ideal for local fault finding and continuity checking of fibres.
-
product
Fibre Optic Converters
In complex testing environments it is often needed that electrical signals have to be transmitted into the chamber or out of the chamber to the test equipment.For that purpose we offer a variety of different interfaces that convert electrical signals into optical signals and back. Such the signal can be transported via fibre optics and is immune against electrical fields.
-
product
Fiber Optic Visual Fault Finder
VFF5
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
-
product
Dual 2 Channel Fibre Optic Mux FC/APC
40-815-022
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
O/E Converter
TIA-525
The TIA-525 optical receiver is a convenient, easy to use optical to electrical converter. It is extremely useful in a variety of laboratory and field service situations where a quick check of the operation of a laser source, optical transmitter, or the output of a fibre optic communications link is required.
-
product
Fibre Optic Laser Encoders
The RLE system is a unique, advanced homodyne laser interferometer system specifically designed for position feedback applications.
-
product
PXI Dual 2 Channel Fibre Optic MU
40-855-322
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Wide Angle High Definition Underwater Camera
Surveyor-WAHD
The Surveyor-WAHD underwater camera is designed to provide a 14% increase in angle of view, from the previous WAHD camera, whilst remaining compact and very competitively priced. It is ideal for ROV inspection tasks, scientific observation and broadcast applications.Video output is available as component (Y/PbPr), utilising standard connectors or HD-SDI on hybrid 75 Ω coaxial or fibre optic connectors, a composite video output is also available.
-
product
Fibre Tracer
FT20
The KD Optics FT-20 is a small, hand-held, visible source used for tracing multimode fibre optic cables and is especially useful for identifing a single fibre in a multi-fibre cable. The unit has a bright LED output with a 2km range and is modulated at 2Hz.
-
product
PXI Quad 2x2 Fibre Optic Mux MU
40-860-342
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
O/E Converter
TIA-3000
The TIA-3000 is an instrument for the laboratory or for field use. This amplified optical-electrical converter can be used with a wide range of oscilloscopes and digitisers to provide the utility of a convenient, easy to use fibre optic probe. Energising the unit, the optical signal presented to it is faithfully reproduced on the CRT of the oscilloscope or digitiser.
-
product
PXI Single 2 x 2 Fibre Optic (M Mode) SC M50
40-860-212-M50
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Next Generation Subsea Attitude and Heading Reference Systems
TOGS
The new TOGS subsea navigation system is built on core TSS fibre optic gyro (FOG) navigation technology with significant improvements in efficiency and functionality. It is available in three standard heading accuracy variants: 0.1° (TOGS1), 0.3° (TOGS3) and 0.5° (TOGS5), all rated for operational depths to 4,000m or 6,000m. Attitude data is delivered via accurate roll/pitch measurement capabilities of 0.01° (TOGS1) and 0.05° (TOGS3 and TOGS5), and a heave performance of 5cm or 5%.
-
product
IVTS In-Vehicle Test Set
The in-vehicle test set was developed to successively measure several active RF amplifiers installed in the vehicle as well as different antenna structures. It offers the possibility to connect 12 DUTs. The DUTs can be connected to an external spectrum analyser via a 1 to 12 RF multiplexer. Each DUT can be individually switched and supplied with an adjustable voltage via a bias-tee integrated in the system. The individual bias voltages and currents are recorded by the IVTS and can be called up on an interactive control panel or via Ethernet and SCPI commands. The complete system can be powered by rechargeable battery and can be operated either via Ethernet, fibre optics or WLAN.
-
product
Utility Detection Radar
DS2000
There’s a lot going on underground that you need to know about before you ever start to dig. The Leica DS2000 Utility Detection Radar finds all potential threats, including non-conductive pipes and fibre optics, increasing safety by lowering the risk of accidently hitting underground assets. Increase safety, speed up work and lower asset management costs with the ability to prevent hazardous outages and collect more information. The DS2000 betters your business by making it safer, faster and more efficient.
-
product
Laser Module
LDM200
Artifex Engineering GmbH & Co. KG
The LDM200 series of laser diode modules are specialized units for high-end applications. The fibre coupled design allows flexible installation and separation of the electrical and optical sections. High quality optics and precision adjustment provide for excellent beam quality and very long collimation distances up to 100m. Customized fixed focus distances may also be provided. The option of choice of pola
-
product
Mini Multimode Power Meter and Mini LED Source
The KD Optics Mini Multimode power meter and Mini LED source are designed for the 850nm and 1300nm testing of multimode links, fibre continuity testing, connector testing, transmitter power testing etc.
-
product
"Signal Transporter"
LTX-5510
The LTX-5510 enables precise conveyance of analogue plus four channels of digital information over fibre optic links ranging from meters to more than 10 kilometers. Incoming analogue data is digitised to 12-bit precision at 50 mega-samples per second and transmitted over optical fibre at a 1 Gb/s data rate.?
-
product
PXI Dual 2 x 2 Fibre Optic Mux SC/PC
40-860-222
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
AIM System Solutions
AIM can provide a wide range of customized solutions:*Special-to Type Test Equipment (STTE)*High Level Bus Analysers (HLBA)*Data Acquisition Recording & Simulation Systems*Aircraft Ground Equipment (AGE)*MIL-STD-1760 Weapon Test Sets*Fibre optic MIL-STD-1553 Stub/ARINC429 Link Extension System (FoMIS/FoL)
-
product
Dual 2 Channel Fibre Optic Mux FC/PC
40-815-122
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
product
PXI Triple 2 Channel Fibre Optic MU
40-855-332
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
E/O Converter
LTX-510
The LTX-510 Electrical to Optical Converter is a convenient device that is intended to transmit analogue or digital signals to a remote location via a multi-mode fibre optic cable. The main applications are situations in which the signal of interest has a high common mode voltage with respect to the measuring equipment.
-
product
Cable Certifiers
LANTEK III Series
New permanent link adapter saves money. Send test data anywhere using IDEAL AnyWARE app. Certifies multimode and single-mode fibre (optional). Professional PDF reports with free software. Certifies twisted pair cabling to TIA/ISO standards. The LanTEK III is an easy to use cable certifier that meets existing TIA and ISO/IEC performance requirements for testing up to Cat 7A/1000MHz. FiberTEK III adapters are used with LanTEK III for fast and simple certification of high bandwidth single-mode and multimode fiber optic cabling including support for encircled flux testing.
-
product
STANAG3910/EFEX Modules
AIM’s STANAG3910/EFEX test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. The latest versions also support avionics discrete I/O. Configurations with dual redundant concurrent HS/LS Bus Controller (BC), Multiple Remote Terminals, and Chronological/Mailbox Bus Monitor operation with full HS/LS protocol error injection/detection, multi-level triggering, advanced capture/filtering and real time bus recording, time stamping and physical bus replay ensure your bus integrity. Support for EFAbus Direct Digital Links (DDL), Fibre Optic DDL (FODDL) and EFAbus Express extensions (Mixed Mode and Dual Mode operation) are available. To support the French ‘Rafale’ aircraft, modules are available with an Electrical Front End. Single Function variants support cost effective solutions. Each module is delivered with a Board Support Package (BSP) containing the onboard driver software, a full Application Programming Interface (API) and detailed getting started and programming guides. Powerful PBA.pro databus test and analysis software is optionally available for all our STANAG3910 modules.
-
product
PXI Single 2 Channel Fibre Optic MU
40-855-312
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Optical signal transmission
Digital
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
