Filter Results By:
Products
Applications
Manufacturers
Couplers
enable a signal to be used in another circuit.
- LBA Group, Inc
product
Digital RF Power Monitor
3024
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Multi Current-Mode-Coupler
Sy629PMC-M-CMC
The Sy629PMC-M-CMC module allows ARINC-629 terminals to communicate directly without the need for an ARINC-629 bus Cable and conventional Current Mode Couplers.
-
product
Digital Output
VME-2170A
The VME-2170A optically coupled digital output board consists of VMEbus compatibility logic,data control logic, four 8-bit output registers, and 32 optically isolated high-level outputs. The board is implemented as a double Eurocard form factor PC board, and provides all necessary address decoding and data transfer control logic to accept both 8- and 16-bit data transfers. Optical couplers isolate the 32 outputs from each other and from the VMEbus.
-
product
Coupler Workstations
Workstations using pure hydrogen gas from a tabletop generator, tank supply, or oxygen, can achieve high enough temperatures to develop Fused Biconic Tapered devices, Power Combiners, Wavelength Division Multiplexers, Thermal Core Expansion devices, and many other products.
-
product
PD Calibrator
PDCAL has excellent pulse-with stability; scale calibration factors are permanently stored inside its flash memory. Thanks to on board photo coupler PDCAL output pulse can be synchronized with the actual line frequency through external surrounding electrical light source systems.
-
product
DURAMAX FUEL SYSTEM TESTER
DFST10
*Test diesel fuel pressure and vacuum on GM 6.6 liter Duramax engines*Includes 6' hose and quick coupler
-
product
Solid State Relays
Panasonic Industrial Devices Sales Company of America
Panasonic offers a wide variety of Solid State Relays including Through-Hole and SMD, High Capacity and Phototriac Coupler Solid State Relays. Triac output components for AC load applications. Advantages include long operational life, high frequency switching, no contact arcs, high contact reliability, and noiseless operation.
-
product
Waveguide Coupler
ZDC8-30W32.9-50G-2389
Crossguide Coupler, Frequency 32.9~50GHz, Coupling 30dB, Waveguide FUGP400, 2.4mm Female
-
product
Coupler Metrology
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Rosenberger provides directional coupler-based measurement techniques as well as probes for comprehensive cross-domain coupling analysis.Nowadays, the introduction of new accessories within vehicles, like rear seat infotainment, smart dashboards, and various advanced driver assistance systems, has increased the demand for high-speed automotive bus systems working in parallel with the high-voltage power networks in electric cars.
-
product
Diesel Compression Tester
34700
Measures cylinder pressure on diesels equipped cars and trucks. Records maximum pressure reached during engine test. Release valve allows for immediate venting and resets gage for repeat tests. Swivel end quick coupler is connected to adapters sold separately. High pressure hose is 16 1/2" long. Gage is scaled from 0-1,000 PSI and 0-70 BAR.
-
product
Taps And Passives
ATX offers the latest innovations in passives for HFC networks, including taps, couplers, splitters and power inserters. The 2GHz XS Series enables MSOs to support DOCSIS® 4.0 architectures, while the 1.2GHz SG Series will maintain a 1.2GHz plant and offers compatibility with Cisco’s popular Surge-Gap portfolio of hardline taps and passives. A bonus feature with the ATX 2GHz taps and passives is the upgradeable faceplate, futureproofing these HFC devices for 3GHz and beyond.
-
product
X Band Coupler With Dual Output Threshold Detector
The X Band coupler with dual output has an input power range of either -5 to +10 dBm, or +5 to +20 dBm. Covering 8.0 to 9.5 GHz, insertion loss is less than 1.0 dB and VSWR is 1.5:1. The coupler/detector has two external resistors providing independently settable threshold TTL outputs. The power flatness is ~0.4 dB and hysteresis is 0.1 dB. Cougar can provide this function in other frequency ranges and input power ranges.
-
product
REM-11175, 16-Channel (Output), 24 V, 2-, 3-Wire Digital Module for Remote I/O
784745-01
The REM-11175 is a digital output module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and … individual modules mounted on a DIN rail. You control the REM-11175 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM-11175 features 2- and 3-wire spring terminal connection methods and circuit and overload protection.
-
product
Avionics Data Bus Tester
Distributed CORVUS
Distributed CORVUS works in conjunction with CORVUS-300 to isolate bus anomalies and fault resolution. The Transmit unit, C-9235-TX, sends 1553 like data pattern through a bus stub and coupler to the Receive unit, C-9235-RX, on another stub. This will measure insertion loss, possible bit errors and correct polarity. The Receive unit can also be used to give a digital scope representation of the active data bus showing signal quality and peak to peak amplitude.
-
product
RF Directional Coupler
Panda Microwave offers RF Directional Coupler, standard coupling values of 6, 10, 20, 30, 40dB, frequency range up to 70 GHz, average power 1 to 50 watts. It is available in N, SMA, TNC, 2.92mm, 2.4mm, connector type. Broadband Directional coupler and Bi-Directional coupler (dual directional coupler) are available. While maintaining exceptional coupling flatness, directivity, VSWR, and insertion loss. These precision couplers and tappers for RF are quality manufactured to precise specifications. Required for accurate coupling at the specified values listed for each product.
-
product
Bias Networks
Macom Technology Solutions Holdings Inc.
At MACOM we offer 18 - 40 GHz bias networks suitable for DC biasing of PIN diode control circuits. Our bias networks function as both RF to DC decoupling networks, as well as a DC return. These bias networks can also be used as bi-directional reactive couplers for Schottky detector circuits in multimarket applications.
-
product
Dual LED Modules
FOD 3106
The FOD Dual LED modules are designed specifically for test instruments application. They allow to have one output for two wavelengths in compact handheld device without couplers. The Module have an original ceramic ferrule that allows to incorporate the module on the front panel of a device and keep the access to the front face of the ferrule for cleaning and polishing.
-
-
product
Trace All Accessory - Inductive Coupler
CZ1803
The CZ1803 is an inductive antenna accessory used to put a signal on any pipe or cable without having to make direct connection to that pipe or cable. You can simply plug the Inductive Coupler into the transmitter and your signal will be transmitted onto your target pipe or cable. When used with the TraceAll locator system, this inductive coupler is suitable for locating all services such as data, electrical, television, telecommunications cables and gas and water pipes.
-
product
Directional Couplers
Directional Couplers designed by BroadWave provide an accurate method for sampling microwave energy. Available in single and dual configurations. We can offer couplers for most applications including power measurements, signal leveling, and frequency measurements.
-
product
Couplers
Smiths Interconnect range of passive coaxial products include couplers of various types (Wilkinson, Directional and Branchline) designed specifically for established reliability applications to provide optimal performance operating in assigned frequencies ranging from UHF to Ku-Band. The couplers featured below have been developed and qualified to operate in extreme operational environments whilst providing designers and system architects with reliable and robust products produced by a manufacturing team experienced in the production of critical application hardware.
-
product
Conducted Immunity Test System
Conducted RF immunity tests acc. to IEC/EN61000-4-6 and BCI tests acc. to ISO 11452-4 and MIL-STD 461 CS 114 Signal generator,RF-power amplifier, RF-power meter and directional coupler (optional) in one 19”-caseStand-alone operation possible with optional available netbookControl-software includedMost important parameters are shown on an integrated displayAutomatic EUT-monitoringOperation via USB port of a PC or NotebookComplete range of CDNs available
-
product
FBT Coupler
TRIPLE WINDOW
MAINTAINS OPTICAL OUTPUT UNIFORMITY.- Telcordia Standard- Minimal effect of Temperature change- High Stability- Low Insertion Loss
-
product
Passive Components
Ducommun millimeter wave products include various passive components including multi-hole directional couplers (PCM), crossguide couplers (PCC), magic tees (PCT), coax power dividers (PPD), bandpass, low pass and high pass filters (PFB, PFL and PFH), waveguide diplexers (PDC), waveguide transitions (PRC and PTW), waveguide to coax adapters (PTC) and waveguide components (PWS, PWE, PWH, PWM and PWT). These passive components cover frequency range from 8.2 to 110 GHz and feature high performance and low cost.
-
product
For accurate testing of headphones, microphones telephones and loudspeakers
Artificial Mouths, Ears, and Couplers
Listen supplies artificial mouths, ears and ear couplers from Brüel and Kjær, GRAS and more.
-
-
-
product
Inductive Coupler
CLAMPMITTER™
The CLAMPMITTER™ is a unique tool for inductive coupling. This self-contained inductive transmitter increases productivity, promotes safety and simplifies locates by condensing the transmitter and inductive coupler into one cordless package. Whether climbing down a manhole or accessing a utility box, the Clampmitter is an easy alternative to suiting up with a full transmitter and wired coupler.
-
product
Splitter / Coupler
Splitters and couplers divide optical inputs into multiple outputs, or combine multiple inputs into one or more outputs. ACP offers a wide variety of splitters/couplers, such as our 1x4 Singlemode Single Fusion Tree Coupler or our Polarization Maintaining Filter Coupler.
-
product
Capacitive Divider
It can be chosen as PD sensor for Techimp PDCheck, PDScope or PDBaseII systems. It is suitable for on line or off line PD tests onrotating machines, for both spot measurements and monitoring applications. A BNC termination is available to connect the coupler through a coaxial cable.
