Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
Acute 2GHz, 34 Channel, TravelLogic Series Protocol & Logic Analyzer With 8Gb Memory
Acute TL3234B+
The TravelLogic Series of Protocol & Logic Analyzers are small enough to fit into your shirt pocket, yet are truly sophisticated logic analyzers, capable of 2 GHz timing analysis, or 200 MHz state analysis, with up to 8 Gb total stackable memory for the 34 channels. They plug into a PC or Laptop USB port making them ideal for the field service technician or engineer, hopping from PC to PC, or taking with them for diagnosis on the road. Also remember that with USB, no additional power supply is needed.
-
product
PXI Vector Component Analyzer, 100 kHz to 26.5 GHz
M9815AS
The PXI vector component analyzer (VCA) enables complex multiport device characterization with continuous wave (CW) and modulated signal measurements.
-
product
Two Port SAS?SATA Analyzer
Sierra M122A
The Sierra M122A is Teledyne LeCroy’s two port SAS / SATA analyzer with special licensing to allow 6 Gb/s protocol capture. This multifunction platform is available with an integrated traffic generation option capable of host and device emulation. There is also a “Jammer” option for stress testing at the system and component level. This model of the Sierra M122A is configured for 6Gbps SAS & SATA protocol capture and can be field-upgraded to support 12Gb/s SAS testing.
-
product
Near-Field Probes 100 kHz up to 50 MHz
LF1 set
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.
-
product
On-Board Systems
OBS-ONE series
HORIBA developed the OBS-ONE series on-board emission measurement system in response to new requirements for exhaust emissions measurement from vehicles being driven on public roads (Portable Emissions Measurement Systems - PEMS). This development has been made possible by reducing the dimensions and power consumption of laboratory grade analyzers and ensuring that the system components have excellent vibration resistance. The OBS-ONE series continuously measures not only the concentration of CO, CO2, THC and NOx, but also measures exhaust fl ow rate and A/F ratio to calculate mass emission and fuel economy.
-
product
PNA Microwave Network Analyzer
N5224B
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Calcmet Software
All Gasmet FTIR analyzers are supplied with Calcmet software. The software collects, stores and visualizes the FTIR spectra of the sample gas and analyzes the concentrations of gas components. Quick and accurate results in easy-to-use package.
-
product
Customized Analyzer Systems
Extractive analyzer systems based on high-quality standard modules and components. Thanks to the configurable design, the analyzer systems can be provided with the optimum specifications to meet the requirements of particular customers. If desired, retrofitting can be carried out easily and cost-effectively by installing analyzers and gas conditioning components. Long-term system support is assured.
-
product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
product
110 GHz Lightwave Component Analyzer
N4372E
The N4372E lightwave component analyzer helps you with optoelectronic tests with its measurement capability of 110 GHz in an extended wavelength range. It also offers RX testing up to 110 GHz in the full 1260 nm to 1620 nm range. It has a built-in optical power meter that enables you to check and control the operating power. The N4372E lightwave component analyzer's optical transmitter input port connects to an auxiliary tunable laser to verify S-parameters over wavelength.
-
product
Radio Vector Tester
Wuhan Sunma Technology Co., Ltd.
Radio & Vector Network Analyzer adopts the advanced digital and RF combination design technology, fundamental wave frequency mixing technology, digital IF processing technology, intelligent power management technology, etc. It comes with features of high precision, small size, light weight, battery power, can measure SWR, Return Loss, Cable Loss, Impedance, DTF, etc, is used to the field test of cable, feeder, and the reflection parameters test of RF components in science and teaching. SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers.
-
product
GC Analyzers
Agilent’s GC Analyzer portfolio can combine multiple methods into a single system, with proven results, and significantly reduce time required from system arrival to final calibration and validation. With our preconfigured gas chromatograph hardware and method-specific separation tools, you can spend more time focusing on sample processing than on method and system development. Our specific GC Analyzer solutions provide the components and specifications to quickly install new methods for a fast return on investment in various application areas, such as environmental, gas impurities, forensics, pharmaceuticals, dissolved gas, energy, and chemical applications.
-
product
NIR & UV-VIS Process & Lab Analyzers
Our Guided Wave complete analytical systems utilize proven Near Infrared (NIR) and Ultraviolet / Visible (UV-VIS) spectroscopic techniques. We deliver a total solution that includes optically matched components and a well-planned calibration approach leading to long-term success and savings. Our state-of-the-art systems are designed for continuous online use, providing real-time data of laboratory quality while thriving in the most demanding processing plant environments. We work with you to tailor a solution for your exact requirements from analyzer to interface.
-
product
Remote Service TV Signal Analyzers
Remote service TV signal analyzers are designed for continuous monitoring of the television distribution systems, their components and other electronic devices. A distinctive feature of these analyzers is the Ethernet interface which allows creating a centralized system for cable network monitoring controlled by the TCP/IP local network.
-
product
PXI Vector Component Analyzer, 100 kHz to 53 GHz
M9818AS
The PXI vector component analyzer enables complex multiport device characterization with continuous wave and modulated signal measurements.
-
product
RF Near Field Probe Set DC to 9GHz
EMF & RF close field sniffer-set for use with any Spectrum Analyzer or Measurement Receiver. The EMC Near Field probe set allows for straightforward pinpointing and measurement of interference sources in electronic component groups as well as execution and monitoring of generic EMC measurement. Our RF near field probe set is especially suitable for: - Pinpointing interference sources - Estimation of interference field strength - Verification of shielding and filtering measures - Identifying faulty components - Detecting circuitry overly sensitive to interference.
-
product
Gas Analysis
Accurate measurement of gases and their concentrations is critical in many applications, and often poses a major challenge. Sensors' experience with different measurement principles, including NDIR, NDUV, and thermal conductivity, along with the ability to provide special combinations of these techniques within our products, enables us to tackle these challenges. In addition, our experience goes into every detail of our gas analyzers, ensuring reliable results, even under harsh conditions. Our skilled team of experts is happy to assist you in finding the optimized solution for your measurement requirements, with either off-the-shelf components or a customized solution.
-
product
Accessory Kit, Type-N to BNC, 50 Ohms
11854A
The Keysight 11854A accessory kit furnishes the RF components required for measurement of devices with 50 ohm, BNC connectors and when using a network analyzer with a type-N configuration. The BNC accessory kit contains two type-N male to BNC female adapters, two type-N male to BNC male adapters, two type-N female to BNC female adapters, two type-N female to BNC male adapters, a BNC male short, and a storage case.
-
product
Launch Analyzer
2440
The 2440 Launch Analyzer is the first fully automated test system for characterizing the optical power distribution of the light produced by VCSEL laser sources, multimode fiber test equipment and launch cords utilized in multimode fiber links. Built on over 20 years of experience testing the transmission and geometric properties of muitimode fibers, the 2440 is the ideal solution for ensuring that source launches comply with applicable international component specifications and measurement standards. The 2440 can be configured for measurements in either or both the 850 and 1300 nm windows.
-
product
CAPS True NO2-NOX-NO Analyzer
Model N500
Teledyne Advanced Pollution Instrumentation
The Model N500 CAPS NOx analyzer uses superior Cavity Attenuated Phase Shift (CAPS) Spectroscopy to measure True NO2, NOx, and NO gases. The instrument combines direct NO2 measurements with highly efficient gas phase titration (GPT) to convert and measure the NO gas component. An automatic baseline reference cycle accounts and compensates for any potential baseline drift due to varying environmental conditions.
-
product
Vector Network Analyzers for LMR
Vector network analyzers are a valuable tool for radio technicians. VNAs allow you to tune frequency dependent components including transmitters, combiners and isolators, circulators, duplexers and filters. With a VNA you can measure and adjust S11 parameters, measure return loss, or analyze and fix response issues. CMT offers compact VNAs ideal for benchtop and field use.
-
product
Power Analyzer
MOTOMEA's Power Analyzer system provides an in-depth analysis of electric drivetrain and power electronic components for electric and hybrid vehicles.
-
product
Micro probes 1 MHz up to 6 GHz
MFA 01 set
The micro probes are used to measure magnetic fields and they have a high resolution. They measure magnetic fields up to 6 GHz, e.g. at signal conductors (150µm), SMD components (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the Bias tee BT 706. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee BT 706 to a spectrum analyzer or an oscilloscope. Langer EMV-Technik GmbH includes correction lines in the delivery. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
product
Spectrum Analyzers
From entry level swept spectrum analyzers to advanced real-time analysis RIGOL provides unprecedented value. Whether you are doing simple signal visualization, integrating wireless technologies into your IoT design, characterizing component performance, preparing for emissions compliance testing or working with complex modulated signals RIGOL has a Spectrum Analyzer to fit your need and budget.
-
product
Impedance Analysis
S96041B
Make impedance analysis measurements of Surface Mount Device (SMD) components on the E5080B vector network analyzer with 16198A-010 10 GHz SMD test fixture.
-
product
3 Phase Power Analyzer
VPA-60080
VEER Power Analyzer VPA-60080 is result of continuous R & D activities. It is an accurate Instrument to test 3 phase & 1 phase electrical Machines due to high sampling rate & simultaneous measurement of parameters. It has no adjustable components inside so, accuracy remains long time. We provide Free Software VEER POWER ANALYZER TOOL with VPA-60080 to communicate with computer which is capable to collect all parameters from VPA-60080 & generates test report. You can see parameters in different view like Digital, Analog, Graphical etc in real time. You can record test data in real time to eliminates Human error in Testing.
-
product
Impedance Analysis For E5061B-3L5 LF-RF Network Analyzer
E5007A
The E5007A provides the impedance analysis (ZA) firmware for the E5061B LF-RF network analyzer. This option enables the analyzer to measure impedance parameters of electronic components such as capacitors, inductors, and resonators. The combination of NA and ZA capabilities further enhances the analyzer’s versatility as a general R&D tool. Basic ZA functionalities including fixture compensation and equivalent circuit analysis are supported by the firmware. The DC biased impedance measurement is possible with the built-in DC bias source provided by the E5061B-3L3/3L4/3L51.
-
product
Wound Component EST Analyzer
19036
Chroma 19036 is the industry's first wound component electrical safety test (EST) analyzer that combines the functions of impulse test, hipot, insulation resistance and DC resistance measurements. It has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement that can comply with the wound components test demands by providing maximum 10 channels output for multichannel scanning tests to save time and labor costs.
-
product
Ethernet
Ethernet and fiber optic networks are critical components in business service delivery. The DataScou... t family of multi-service network analyzers enables providers to equip technicians to install and troubleshoot next generation networks effectively, while continuing to support legacy transport services. Tempo Communications offers service providers powerful, all-in-one solutions that span future and past technologies, making the transformation from legacy transport circuits to advanced multi-gigabit services an easy one. The DataScout family is designed to ensure maximum efficiency while lowering costs associated with installing, maintaining, and troubleshooting networks.Show less
-
product
4-in-1 OSLT Calibration Kit, DC to 50 GHz, 2.4 mm (m)
CK564A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Robotic Intelligent Laboratory System
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
Is able to determine calorific value, total sulfur, internal moisture, ash, volatile matter, CHN content and other indicators by robot technology. The main components include intelligent robot, automatic analytical instruments (calorimeter, sulfur analyzer, proximate analyzer, and elemental analyzer), automatic bottle opener and sampling device, automatic weighing device, oxygen vessel loading and cleaning device, electrical control system, and laboratory analysis and data management software.
