Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
High Voltage 50 Pin D-Type Connectors
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
Audio Cable Tester
CBT-500
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
product
Heavy Duty Circuit Tester with 12' Retractable Wire & Battery Clip
27300
Features an extra long wire that stretches up to 12 feet for use, then automatically retracts. Quickly and easily check electrical circuits and accessories on 6 and 12 volt systems. Great for use on cars, trucks, boats, trailers, motorcycles, airplanes and snowmobiles. Heavy duty ground clip with insulator. 3 1/4" standard length probe
-
product
Digital Bridge
KT-8280
Large 0.78" LCD , 1999 counts, all enunciators displayVector MeasurementFour Terminals MeasurementDissipation Factor MeasurementWide range, high accuracyTest Frequency: 1 KHzPower consumption less 5 mAPower Sources:9V transistor type battery (Neda 1604)Complete with : Four Terminal Mode alligator clip leads, rubber holster, AC power adapter, carrying bag
-
product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
product
USB
Universal serial bus, or USB, is an industry standard that defines the cables, connectors and communication protocols used to connect computers and peripherals. ST's portfolio covers a wide range of products designed for USB data (transceivers) and/or power applications (battery chargers and charger detection systems).
-
product
Handheld Water Quality Meters
LAQUA WQ-310-K
- Single channel- Large colour graphic LCD screen (70 x 52 mm) with backlight - Built-in foldable meter stand- IP67 waterproof and dustproof- Battery and USB powered- Eco-friendly, shock-proof, scratch-resistant, and non-slip- Built-in sensor holders- Efficient sensor locking mechanism- Sensor's LED light as reading stability indicator- No sensor adapter needed for attaching multiple sensors together- Compatible with conventional electrodes having BNC and phono connectors and long cables- Sensor status indicator- Temperature sensor indicator- °C & °F temperature units- Sample ID setting- Detailed calibration data- Auto stable, Auto hold, and Real time measurement modes- Customizable meter kit - up to 5 meter-sensor kit combinations- Hands-free testing- Ergonomic design- Multi-language options- Versatile channel and adaptive display- Automatic sensor recognition function- Data transfer via USB or wireless communication- Printer communication- 3 years meter warranty
-
product
Ohm-Stat Digital Display Megohmmeter
Measures resistivity RTT, RTV, and RTG 103-1012 ohms/sq., ohms, ohm-cmRelative humidity 10% 90% RHTemperature 32oF 100oFDigital display: easy to interpretNIST calibration includedIncludes chair probe to measure smocks, earth ground, chairs, and resistance probes: $400 value for freeResistivity probe built in the bottom of meterProduct conforms to the ESD S.20.20 spec standardsCE mark includedThe kit includes, two (5) lb probes, coil cords, hard carrying case, battery, 110v or 220v adaptor, garment clips, chair probe, and ground circuit tester
-
product
Digital Multimeters
Triplett Test Equipment & Tools
compact digital multimeter with a backlit LCD display. It offers a large variety of measurement features including AC/DC Voltage, DC Current, Resistance, Continuity, Diode Test, Transistor hFE, and Temperature. The rubberized boot provides impact and drop resistance in a sleek ergonomic design, and the user-friendly Auto Power Off feature helps maximizes battery life. The Model 1101-B is well suited for a variety of commercial and residential applications such as security, home theater, electrical, HVAC installations and more. Includes test leads with alligator clips, Type K bead probe and battery (9V).
-
product
Digital Engine Analyzer/Multimeter
385A
The #385A has many of the necessary features required for today’s automotive diagnostics. Use frequency readings to test crankshaft and camshaft sensors, for example. The #385A comes equipped with an RPM pick-up, probe test leads, alligator clip test leads, protective holster, instructions and installed 9V battery. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
product
Cable Phasing Meter
4183 CP
Standard Electric Works Co., Ltd
● Safely operates at low voltage ● Measures system voltage.● Measures capacitance of test point if system voltage is known.● Checks phase rotation of cables.● Phases out cables.● Rugged - comes with portable case.● Operates from potential test point of elbow connec-tors.● Battery operated.
-
product
Cable Tester
CT-3
Monacor International GmbH & Co. KG
Cable TesterFor cables with the following connectors:-XLR (3-pin)-XLR (5-pin)-6.3mm jack-RCA--DIN (up to 8 pin)-banana plug-Speakers (2-, 4-, 8-pin)-USB A-RJ45*LED error indicator, adjustable per contact via selector switch*Acoustic and optical continuity test via enclosed test leads*LED battery status indicator*Robust metal housing*Power supply via 9 V block battery (not included)*Abmessungen 112 x 60 x 190 mm*Gewicht 800 g
-
product
Single Channel USB Programmable Instrumentation Amplifier
USBPIA-S1
The USBPIA-S1 stand alone USB controllable module provides a single channel of high-quality instrumentation amplifier and optional AC coupling, for front-end signal conditioning compatible with all popular A/D converter devices. The USBPIA-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPIA-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPIA-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
product
Battery and Alternator Analyser for 12V DC Systems
1176
Checks battery charge level and alternator output level. 880mm of insulated cable with test probe and earth (crocodile) clip. For 12V DC systems only. Display packed.Warning: For testing DC circuits on vehicles within the voltage range only. Not suitable for testing mains supply AC circuits.
-
product
Battery Impedance Tester
KT-97A
3 1/2 digits, Max. reading 1999Test battery Impedance, resolution up to 0.01mΩTest Voltage onlineFit to test battery: lead-acid, Li-ion; Ni-HM, etcTest the battery used in UPS,automotive,mobile phone,etcPure AC 1,000Hz test mode4 wire test clip with high accuracy
-
product
Bond Meter Kit
R1L-BR1
The TEGAM Model R1L-BR1 bond meter is a purpose built, rechargeable battery powered portable instrument for ground bond measurements. The R1L-BR1 comes with BCP-10 push-pin probes and KAK-1M Kelvin alligator clips, it is all housed with in a ruggedized case. It can accurately make measurements with a resolution of 1 microohm. It has been selected and deployed in Afghanistan for use on the Kiowa Warrior Armed Reconnaissance Helicopter.
-
product
LAN Cable Tester
PA-01D
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
product
Precision Micro Ohmmeter
BS407
High basic accuracy of 0.1%Wide range of 1 µΩ to 20 kΩCurrent reversal switch for detecting thermal EMF effectsCurrent diversion switch for easy zeroingFour terminal measurement using Kelvin clip leads (supplied)Battery operation with built-in charger20mV clamp for "dry circuit" testing
-
product
PRO Test Lead Kit
142
#142 Pro Test Lead Kit includes our premium set of interchangeable specialty test probes designed for automotive use. This lead set features an extended length of 64 inches. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. In addition, the large Crocodile Clips are good for clipping to grounds and battery terminals. Includes roll up storage pouch to keep your leads organized. These are compatible with most DMM’s and scopes.
-
product
Network Analyzer, Lan Tester, LED
72-6290A
The 72-6290A is a multi-modular Cable Tester (LAN Tester) with LED meter display. Requires 9V battery for this modular cable tester. Used with RJ-45, RJ-12, RJ-11 connectors and USOC4, USOC6, USOC8 cables.
-
product
Tone Generator
140BMC/6P
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
product
Hardy Shaker
HI-913
This Hardy Shaker provides the ability to set the amplitude and change the frequency range without the amplitude changing. This automation makes conducting a test easier. A test can be conducted on a vibration transducer and manually recorded. Multiple tests are not saved; for multiple tests use the HI-903 or HI-803 units. The HI-913 is used for testing from 7 to 10,000 Hz, it offers adjustable frequency and vibration levels. This provides a reference source for verifying the accuracy of vibration transducers, connectors, cabling and instruments or instrumentation systems. The HI-913 has a ruggedized suspension system that can support heavy transducers (up to 800 grams - see frequency limits in the manual). The HI-913 has a built-in battery charger that can operate on 120 or 240 VAC. The unit comes in a rugged Pelican case.
-
product
CAT III Digital Multimeter
82600
Measures AC/DC voltage/current up to 600V and 10A, capacitance, diode, duty cycle, frequency, resistance, temperature and transistor. Includes 13 Functions and an operating temperature range between -40° to 1000°C. Features manual or auto shutdown after 15 minutes of inactivity, protection against overload at all ranges, data hold, low battery indicator and warning alarm. Also includes a LED flashlight for low light situations. Rubber outer case adds protection against drops and a stand bracket to hold meter at viewing angle and test probe holding clips.
-
product
Linemen's Test Set
TeleTalker 330
Triplett Test Equipment & Tools
The Triplett TeleTalker™ 330 is a high performance lineman's test set with a weather resistant seal. This butt set offers many standard features not found on more expensive models like dedicated store / redial buttons, adjustable volume, Pulse and Tone dialing, and more. The high impact and weather resistant case allows for this product to be used in all demanding industry settings and features a full 3 year warranty. The user-friendly layout helps installers get the job done effectively with ease. The TeleTalker™ 330 requires no battery for main use and can store up to 10 frequently dialed numbers. Complete with angled bed of nails (JS Popper) test clips.
-
product
Professional Cordless Circuit Tester
CT8002
No Ground or clip required. No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance Electronic circuitry. Safety V-groove needle accessory for piercing and carrying. Negligible current draw ( 20 micro-amps) is 10,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 3 and 28 Volt DC in battery powered systems.
-
product
Automotive Test Lead Kit
143
Test Lead Kit includes our basic set of interchangeable specialty test probes designed for automotive use. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. The large Crocodile Clips are good for clipping to grounds and battery terminals. Roll up storage pouch keeps your leads organized.
-
product
Handheld Water Quality Meters
LAQUA WQ-330-K
- Triple channel- Large colour graphic LCD screen (70 x 52 mm) with backlight - Built-in foldable meter stand- IP67 waterproof and dustproof- Battery and USB powered- Eco-friendly, shock-proof, scratch-resistant, and non-slip- Built-in sensor holders- Efficient sensor locking mechanism- Sensor's LED light as reading stability indicator- No sensor adapter needed for attaching multiple sensors together- Compatible with conventional electrodes having BNC and phono connectors and long cables- Sensor status indicator- Temperature sensor indicator- °C & °F temperature units- Sample ID setting- Detailed calibration data- Auto stable, Auto hold, and Real time measurement modes- Customizable meter kit - up to 35 meter-sensor kit combinations- Hands-free testing- Ergonomic design- Multi-language options- Versatile channel and adaptive display- Up to 3 simultaneous calibrations and measurements- Automatic sensor recognition function- Data transfer via USB or wireless communication- Printer communication- 3 years meter warranty
-
product
Optical Test And Measurement
Any type of fiber optic interconnection requires its interfaces to be free of dust and scratches in order to reach the lowest transmission loss. Small, handheld and battery powered inspection tools are available from AMS Technologies for inspection of fiber optic connectors in the field as well as high resolution type microscopes suitable for use in a production environment for qualifying the endface preparation. Additional S/W tools can support the user in making a quick decision if a certain defect is acceptable or if the surface fault disqualifies it for further use. Small and lightweight test equipment for measurement of the transmitted power in an optical fiber is needed wherever technicians handle optical fibers. Our product portfolio comprises light sources for various wavelengths, power meters for the visible and infrared and integrated solutions for sources and meters as well as optical time domain reflectometers (OTDR) coupled with visible wavelength light sources for easy fault detection within a fiber optic link.
-
product
Extended Battery Banks
Falcon Electric’s extended battery banks provide extra battery runtimes from minutes to hours with our SSG and SSG-RP online industrial UPS systems. The rackmount banks are easily daisy-chained with DC plug-and-play connectors. Simply determine your application requirements and select one of these battery bank options.
-
product
Tow Doctor™ Trailer Side Test Unit
50928
Hopkins Manufacturing Corporation
Specifically designed so that one person can make sure a trailer has been wired properly and all functions are working. Plug the Tow Doctor™ into the trailer connector and the power cord into a battery source and cycle through the trailer lighting functions. Includes 7 Blade, 6 Round and 4 Flat test connectors and durable carrying case.
-
product
Cable Test Box
Cables are a critical part of any sensor measurement system and damaged cables cause frequent delays during test setup. PCB has developed a relatively simple device to test cables on a channel by channel basis for BNC, 10-32, and 5-44 coaxial connectors. Simply connect both ends of the cable and faults will be indicated for shield failure, conductor failure, or short circuit shield to conductor. Power is provided by a single, replaceable 9 volt battery.
