Filter Results By:
Products
Applications
Manufacturers
Baseband
The original state of frequencies prior to modulation.
-
product
PMC Compatible Wizard Interface
PMC-Wizard
The PMC-Wizard is intended for use in ultra high-speed bidirectional point-to-point data transmission systems. The primary application is to provide very high-speed I/O data channels for point-to-point baseband data transmission over controlled impedance media of approximately 50 Ω. The maximum rate and distance of data transfer is dependent upon the attenuation characteristics of the media, and the noise coupling to the environment
-
product
Baseband Programmable VGA-Filters
Analog Devices’ RF VGAs, IF VGAs, and variable gain control products offer the high performance needed for communications, instrumentation, and military designs. The portfolio includes continuous analog linear in dB products based on X-AMP® interpolation architectures and digital step controlled products providing as fine as 0.25 dB step and linear in volts digital control. Furthermore, ADI RF VGAs are highly integrated with digitally controlled multipole analog filters integrated on-chip as well as AGC circuits for automatic level control.
-
product
L-Band RF Tuner and 4-Channel 200 MHz A/D with Virtex-6 FPGA - 6U VPX
Model 58690
- Two L-Band tuners accept RF signals from 925 MHz to 2175 MHz- Two programmable LNAs boost LNB (low-noise block) antenna signal levels with up to 60 dB gain- Two programmable analog downconverters provide I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Four 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
PXIe-5645, 6 GHz, 80 MHz Bandwidth, RF and Baseband PXI Vector Signal Transceiver
782377-01
6 GHz, 80 MHz Bandwidth, RF and Baseband PXI Vector Signal Transceiver—The PXIe‑5645 combines a vector signal generator and vector signal analyzer with FPGA-based real-time signal processing and control into a single device, also known as a VST. Because of this software-designed approach, the PXIe‑5645 offers the flexibility of a software defined radio architecture with RF instrument class performance. The PXIe‑5645 features a high-performance, differential or single-ended baseband I/Q interface. This interface allows the PXIe‑5645 to address many additional applications, such as testing both the upconverted RF and downconverted baseband signals of a device with a single instrument.
-
product
Automotive Audio Processors
ST’s wide portfolio of analog and digital signal processors covers the full range of features and channel configurations for the car-audio application spectrum, from low-end solutions to high-end premium audio systems. More than 40 analog signal processors offer a large choice for the number of inputs, number of output channels, and baseband audio functions, including EQ, dynamic compressors, subsonic filters, and more. Alternatively, a fully digital solution with embedded 20-bit audio ADCs and DACs is based on a proprietary 24-bit DSP specifically crafted for audio applications.
-
product
PXI-5652, 6.6 GHz RF Analog Signal Generator
779670-02
6.6 GHz PXI RF Analog Signal Generator—The PXI‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
PXI-5142, 100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope
779587-01
100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope—The PXI-5142 high-resolution oscilloscope has two channels that are capable of high-resolution, low-noise measurements with up to 100 MHz of bandwidth and onboard resources for quadrature digital downconversion and baseband I/Q decimation. This device is ideal for communications measurements and applications that require interfacing with a RF downconverter. The PXI-5142 also features PXI synchronization and data streaming capabilities.
-
product
DC Coupled, 14-Bit Digitizer For ExpressCard 54, 2 Channels 150 MS/s
EC14150D
The EC14150D (EC) is an DC-coupled dual channel waveform capture board that provides a remarkable combination of high speed and high resolution sampling along with a very large memory capacity all in a very compact and low power consuming ExpressCard form factor. At 4.5 W, the EC represents one of the lowest power consuming digitizer cards ever created for its class. Signal frequencies up to 200 MHz can be accurately captured either in baseband or in higher order Nyquist zones using under-sampling techniques. Where DC-coupling is required, the EC14150D should be considered.
-
product
802.11ad Testbed, Reference Solution
Generate and analyze 802.11ad fully coded PHY waveforms for complete component, subsystem, and system performance at baseband, IF, and millimeter-wave. This Reference Solution combines Keysight Technologies software and hardware to provide a flexible testbed for 802.11ad waveform generation and analysis. Software provides the flexibility to generate and analyze 802.11ad waveforms with a wide range of different attributes. Hardware provides the flexibility to support baseband, IF, and millimeter-wave test planes. Create waveform sequences with unique 802.11ad packet structures including Modulation Coding Scheme (MCS), packet length, payload data type, and interpacket gap length, etc.
-
product
AC Coupled, 14-Bit Digitizer For ExpressCard 54, 2 Channels 150 MS/s
EC14150A
The EC14150A (EC) is an AC-coupled dual channel waveform capture board that provides a remarkable combination of high speed and high resolution sampling along with a very large memory capacity all in a very compact and low power consuming ExpressCard form factor. At 4.5 W, the EC represents one of the lowest power consuming digitizer cards ever created for its class. Signal frequencies up to 200 MHz can be accurately captured either in baseband or in higher order Nyquist zones using under-sampling techniques. Where DC-coupling is required, the EC14150D should be considered.
-
product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - 3U VPX
Model 54891
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Optional optical interface for data streaming- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Dual-Band RF Tuner and 4-Ch 400 MHz A/D with Kintex UltraScale FPGA - 6U VPX
Model 58891
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Four 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Four FPGA-based multiband DDCs (digital downconverters)- Two Xilinx® Kintex® UltraScale™ FPGA- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
L-Band RF Tuner and 2-Channel 400 MHz A/D
Model 78891
Accepts RF signals from 925 MHz to 2175 MHz, Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm, Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz
-
product
Digital Signal Processing (DSP)
Digital signal processing (DSP) affords greater flexibility, higher performance (in terms of attenuation and selectivity), better time and environment stability, and lower equipment production costs than traditional analog techniques. Components available today let DSP extend from baseband to intermediate frequencies (IFs). This makes DSP useful for tuning and signal selectivity, and frequency up and down conversion.
-
product
PXIe Digitizer: 500 MSa/s, 14 bit, 200 MHz
M3102A
The M3102A PXIe digitizer is ideal for general purpose digitizer automated test requirements. It offers high channel density with an advanced data acquisition systems (DAQ). The optional real-time sequencing, inter-module synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including angle of arrival (AoA), baseband electronics designs, wireless device manufacturing and multi-channel coherent signal acquisition.
-
product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - XMC
Model 71791
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O
-
product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 3U VPX
Model 52791
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x4- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Vecor Signal Generator
SMM100A
The R&S®SMM100A vector signal generator provides remarkably good RF characteristics across the entire frequency range from 100 kHz to 44 GHz. The instrument covers the bands below 6 GHz used by existing wirelessstandards as well as the newly defined bands for 5G NR FR1 and Wi-Fi 6E up to 7.125 GHz and the 5G NR FR2 bands up to 44 GHz.The internal baseband generator in the R&S®SMM100A supports a maximum RF modulation bandwidth of 1 GHz. Digitally modulated broadband signals can thus be generated as required by the prevalent wireless standards. The R&S®SMM100A is well prepared for future bandwidth requirements.
-
product
Standards Reference for Test Systems PXI Card
GX1034
The GX1034 offers PXI system designers the capability to develop a system re-certification strategy that employs only internal system resources. By incorporating the GX1034 as part of a system configuration, it is possible to develop a system accuracy verification strategy that can recertify a system's source and measure baseband instrumentation resulting in simplified support / maintenance logistics and improved system availability.
-
product
STEREO PERFORMANCE METER
SPM-1
The SPM-1 measures the stereo content present in any left and right audio program material. It measures 0-50 dB separation on live program material by cross correlating the right and left base-band audio information.
-
product
PXIe-5450, 145 MHz Bandwidth, 16-Bit, 128 MB, I/Q PXI Waveform Generator
780419-01
PXIe, 145 MHz Bandwidth, 16-Bit, 128 MB, I/Q PXI Waveform Generator—The PXIe‑5450 is a 145 MHz, dual‐channel arbitrary waveform generator optimized for I/Q communications signals. It is an ideal instrument for testing devices with I/Q inputs, or as the baseband component of an RF vector signal generator. The PXIe‑5450 also features onboard signal processing (OSP) functions that include pulse shaping and interpolation filters, gain and offset control, and a numerically controlled oscillator (NCO) for frequency shifting. The PXIe‑5450 also features advanced synchronization and data streaming capabilities.
-
product
Modulated Signal Creation Software
ArbIQ
The ArbiQ Software package allows wireless design and manufacturing engineers to use the most flexible signal generation tool, the Arbitrary Waveform Generator, to solve almost all their wireless test stimulus needs at baseband or IF/RF levels, no matter if the required signals of analog or digital.
-
product
MultiStandard Advanced Monitoring Probe
EdgeProbe Advanced MultiStandard
The ideal tool for accurate & cost-effective monitoring probe for:DTV terrestrial transmission (DVB-T/T2, ISDB-T/Tb)DTV cable transmission (DVB-C/C2)DTV distribution over satellite (DVB-S/S2, T2-MI, OneBeam, MPTS)DTH uplink and reception (DVB-S/S2, MPTS)Digital Radio transmission (DAB/DAB+/T-DMB)Combine any two RF standards in one single 1RU device.Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing Digital TV & Radio network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor the RF signal, through its RF inputs (up to 4 in 1RU), as well as the baseband transport before modulator, through its ASI and IP inputs.
-
product
WiGig RF Tester
IQgig-RF Model B
When used in conjunction with IQgig-IF, an optimized test solution for conducted testing of WiGig chipsets and baseband modules, the IQgig family products provide a total test solution for R&D characterization and high volume manufacturing.
-
product
PXIe Arbitrary Waveform Generator, 500 MSa/s, 16 bit, 200 MHz
M3201A
The M3201A PXIe arbitrary waveform generator is ideal for general purpose AWG automated test requirements. It offers high channel density with high-quality output with low phase noise. The optional real-time sequencing, intermodulation synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including envelope tracking (ET) and DPD (part of PA/FEM reference solution), MIMO, baseband electronics design, wireless device manufacturing, ATE, beamforming and other multi-channel coherent signal generation and multi-channel signal generation.
-
product
RF Signal Generator
DSG3000B
The DSG3000B Series offers continuous wave high power carriers up to 13.6 GHz, standard AM/FM/ØM analog modulation up to 3.6 GHz, and I/Q modulation and I/Q baseband output up to 6.5 GHz on the models ending in "IQ". It is an ideal tool in various fields such as communication, computers, instrumentation, R&D, education, production and maintenance.
-
product
PXI-5142, 100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope
779587-02
100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope—The PXI-5142 high-resolution oscilloscope has two channels that are capable of high-resolution, low-noise measurements with up to 100 MHz of bandwidth and onboard resources for quadrature digital downconversion and baseband I/Q decimation. This device is ideal for communications measurements and applications that require interfacing with a RF downconverter. The PXI-5142 also features PXI synchronization and data streaming capabilities.
-
product
RF Test Spectrum Measurements over CPRI
Integris 3000
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
product
PXIe-5450, 145 MHz Bandwidth, 16-Bit, 512 MB, I/Q PXI Waveform Generator
780419-02
PXIe, 145 MHz Bandwidth, 16-Bit, 512 MB, I/Q PXI Waveform Generator—The PXIe‑5450 is a 145 MHz, dual‐channel arbitrary waveform generator optimized for I/Q communications signals. It is an ideal instrument for testing devices with I/Q inputs, or as the baseband component of an RF vector signal generator. The PXIe‑5450 also features onboard signal processing (OSP) functions that include pulse shaping and interpolation filters, gain and offset control, and a numerically controlled oscillator (NCO) for frequency shifting. The PXIe‑5450 also features advanced synchronization and data streaming capabilities.
