Filter Results By:
Products
Applications
Manufacturers
Power Calibration
Verify power measuring instruments accuracy.
See Also: Calibration, Calibrators, Display Calibration, Calibration Standards, Calibration Software, Calibration Services, Calibration References
- Pickering Interfaces Inc.
product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 37-pin D-type Connector
40-153-104
The 40/42-153-104 is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A. User connection is via a 37-pin D-type male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
10 MHz To 67 GHz LAN Thermal Vacuum Compliance Power Sensor
L2067XT
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
Web Sensor with PoE
T7610
PoE Web Sensor with built-in temperature, relative humidity and atmospheric pressure sensors.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Power over Ethernet feature according IEEE 802.3af is supported. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
product
Switch Amp
One of many potential designs, Teledyne RF & Microwave's switched amplifier covers 100 to 2000 MHz, providing 18 dB gain, phase matched to within ±1.0 degree. The primary RF input and a secondary calibration signal input are switched, then amplified, and split to two outputs. Gain balance between any of the two outputs is ± 0.5 dB. Output power at 1 dB compression is +14 dBm and input/output VSWR is 2.0:1 maximum.
-
product
Digital Pressure Gauge
Huaxin instrument (Beijing) Co., Ltd
Reputed as a specialized pressure measurement solution provider, Huaxin offers an excellent selection of digital pressure gauges. Unique industrial design and state of the art technology have made our digital pressure gauges an ideal pressure calibration instrument for various applications. Depending on high and low temperature aging and temperature compensation processes before delivery, they feature guaranteed accuracy and stability. The digital gauges have been extensively used in power, metallurgy, chemical, measuring and military industries for calibrating precision pressure measurement devices.
-
product
Workstation For Acoustic & Vibration Engineering
imc WAVE 2022
imc WAVE is a modular, powerful software platform for noise and vibration analysis (NVH analysis). From noise investigations in road tests to structural analyses on the test bench and vibration tests on machines: with different imc WAVE analyzers, you can evaluate a wide range of applications without having to be an expert yourself. In this way, you can also easily and reliably obtain standard-compliant analysis from the fields of noise and sound power analysis, structure analysis as well as the evaluation of the analysis of vibrations and of rotating machines. imc WAVE guides you step by step through the settings, from device configuration to calibration and measurement. In the end, you evaluate your data professionally and then receive a report that is ready to print. The modular software specializes in the following topics.
-
product
Digital Power Meter
2406B
‧Simultaneous display of W, A, V (PF or Hz)‧True RMS V, A, W‧Auto calibration via computer‧Data Hold∕Range Hold function‧Hight immunity to external noise‧CT ratio (1～99)‧REF function (0.800 ～ 1.200)‧Aux. power is AC 90 ～ 260V, 50/60Hz‧RS-232 interface (option)
-
product
10 MHz To 54 GHz LAN Thermal Vacuum Compliance Power Sensor
L2066XT
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
Standard Gain Horns
Standard gain horns can be used to experimentally determine the gain of other antennas by using the substitution method. The standard gain horn and the antenna under test are alternately connected to a well matched detector system in order to compare their relative power levels. The power level difference is then added to the appropriate level of the calibration curve to determine the absolute gain of the antenna under test.View more Standard Gain Horn Antennas
-
product
10 MHz To 6 GHz LAN Wide Dynamic Range Average Power Sensor
L2051XA
Frequency range of 10 MHz – 6 GHzLAN connectivity with a wide dynamic range of -70 to +26 dBm for small signal measurementsFast real-time measurement of 50,000 readings/secReal-time measurement with zero dead time to ensure every single continuous pulse is measuredAverage mode time-selectivity function allows full dynamic range for average and time selectivity average power measurementsInternal zero and automatic calibration saves time and reduces measurement uncertaintyA BenchVue software license (BV0007B) is now included with your instrument. BenchVue makes it simple to connect, control instruments, and automate test sequences
-
product
Digital Multimeters
*5½-digit resolution to 8½-digit resolution DMMs*6ppm basic voltage measurement accuracy on the 8½-digit DMM for calibration laboratories*Fast, 1 Msample/s sampling speed to capture complex, low level current profiles from IoT devices or other wireless devices*Sensitivity of 1 µΩ and 1 pA to test low power devices for research, design, and manufacturing test*A wide range of measurement functions such as DC and AC volts, DC and AC current, two- and four-wire Ohms, continuity, frequency, period, RTD, thermistor, and thermocouple temperatures, diode test, and capacitance*Numerous interface options including LAN/LXI, USB-TMC, GPIB, and RS-232 for data acquisition and automated testing*Intelligence to execute tests and create customized measurements with minimal PC interaction*Measurement expansion up to ten channels
-
product
Ultrasonic Flaw Detector
MFD660C
MFD660C intelligent digital ultrasonic flaw detector, Mitech concentrated years meticulously developed premium product, has a lot of advantages like unique design, sophisticated manufacturing, convenient operation, powerful function. It had received customers' favored since its inception. It can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. With full digital 640X480 TFT LCD display, it can select the operating interface style and the LCD brightness according to environment. With humanizing interface design, the waveform show delicately. It can find the defects clearly in full screen. Single hand capable for holding operation, the curve making, probe calibration and other conventional operation can be completed automatically. Core processor CPU with 400M main frequency, it can complete the complex run quickly and realize intelligent defect analysis. Low power design with large capacity and high performance lithium ion battery module， it can work more than 10 hours continuously. Full English master-slave menu, emphasizing on user experience, collecting shortcut keys, digital shuttle rotary wheel, cross menu three operating ways in one body, customers with different habits can operate it freely. It supports many languages. Its waterproof, oil proof, dustproof function can achieve IP65 protection level. It is the necessary professional precision instrument for defect detection, quality control, on-line safety monitoring and life evaluation in fields of oil, chemical, metallurgy, shipbuilding, aviation, railways and so on.
-
product
Optical Power Meter & VFL
TM263
◇ Self Calibration◇ Set the Auto Off◇ Wavelength Memory function after turn off the tester◇ High Accuracy, high ,High sensitivity, high linearity◇ Stable VFL Output◇ USB Charge port◇ FC,SC Connector◇ 18650Li-ion Battery◇ Lower power consumption design, long standby time◇ Rubber Out shell, increased the protective properties for field work
-
product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
product
Pressure Calibrators
AMETEK Sensors, Test & Calibration
Our pressure calibrators offer a wide variety of features, accuracies, and pressure ranges. Included are intrinsically safe percent of reading calibrators, reference data recorders, wide-range dual sensor calibrators, and calibrators with built in pressure pumps. Many of our calibrators also offer current measurement, voltage measurement, 24 volt loop power supplies, and even complete systems with pressure pumps and calibration software. In many cases, one handheld calibrator can replace multiple instruments, reducing ongoing recalibration and maintenance costs.
-
product
10 MHz To 54 GHz LAN Wide Dynamic Range Average Power Sensor
L2056XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
Current Loop Calibrator
LC-100
The Current Loop Calibrator an accuracy of 0.015% and a 0.001 mA resolution. The loop calibrator can simulate, power, and measure two-wire transmitters. With automatic Step and Ramp functions, the precision loop calibrator also enables remote calibration of 4-20mA devices.
-
product
Torque Measuring and Monitoring System
WISER 4000
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
product
MPI Fully Automatic Probe Systems
MPI Advanced Semiconductor Test
Addressing the RF and High Power communication devices and discrete passive components production test market requirements, MPI introduced the TS2500 200 mm fully automatic probe system series. The system is based on industry leading production equipment from the Photonics Automation Division and incorporates decades of experience in RF and High Power measurement techniques from the MPI’s Advanced Semiconductor Test (AST) Division in combination with other AST products such as RF Probes, related calibration technology, and High Power accessories.
-
product
Standard Voltage Transformer
HJ / 635
Wuhan Huatian Electric Power Automation Co., Ltd.
It is mainly designed for the voltage transformer calibration standard of basic power supply and production department.
-
product
DC Power Solutions
Solve your power measurement challenges with application-specific software and our reliable power hardware. Use our standard or semi-custom hardware solutions to achieve the optimal test configuration for your application. Keysight’s global network makes it easy to replicate solutions, as well as maintain your installed equipment. Calibration and repair are available through global service centers as well as on-site.
-
product
Low Current DC/AC Clamp Meter
SE-07
Max.error by earth magnetic:≤±30mA1/f noise level :0.5mADisplay:3 3/4 digits LCD display with 3999 countsJaw size: 5mm(Max)Range:400mA/4AResolution:0.1mABand wide up to 1KHzOver range indication:Display“0L" or“-0L”Auto range,Auto power off,Auto zero adjustReading Rate:2.5 readings/secAuto Calibration
-
product
High Power RF Calibration System
HPC
The TEGAM High Power Calibration System is the complete automated solution for calibrating through path and terminating RF power measurement devices from multiple manufacturers. It includes the signal generation, amplification and filtering necessary to achieve or exceed the devices original specifications with the most accurate High power measurement system available. Calibrate High Power RF Sensing devices up to 250 W with uncertainty less than 1%.
-
product
Portable Digital Manometer
PS309
Featured are an integral variable reluctance transducer, solid state electronics module, 3 digit liquid crystal display (LCD)* and battery pack with six 1.5V penlight cells for truly portable operation. The units can also be powered from an external DC power supply or AC battery eliminator (converter) module. The transducer features all corrosion resistant materials in contact with the pressure media (both ports in differential units), very low internal cavity volumes and ultra-low volumetric displacement with full-scale pressure excursion. Transducer calibration is unaffected by dielectric properties of the sensed fluid. Gauge and differential transducers may be disassembled and range changed by simple diaphragm replacement.
-
product
Bench Power Supplies
Series ABC
Kepco¹s ABC bench power supply embodies the latest features: keyboard data entry, interactive digital display, integral GPIB support, software calibration, high frequency switch mode conversion, wide range input (85-264V a-c) and power factor correction. It meets the EN 61000-3-2 harmonic limits. A built-in EN 55022 Class B input EMI filter is provided. Integral External Trigger and RS 232 ports are now standard features.
-
product
Validator Torque Wrench Tester
The Validator is designed for testing and calibrating torque wrenches. This tool is not suitable for power tools. Ideal for checking torque tools on production floor daily or weekly to ensure the tools aren't falling out of calibration. Using a quality torque tester makes a safer world through accuracy and precision. Measuring torque is essential for companies to ensure their product’s quality, safety and reliability isn’t compromised. The failure of a three-cent fastener that isn’t properly tightened can lead to catastrophic or latent failures.
-
product
Power Measurement
Precision Acoustics manufactures Radiation Force Balances and Check Sources which can be used to measure ultrasound power according to the IEC Standard 61161. All products are supplied with a calibration from The National Physical Laboratory, LONDON.
-
product
Hipot Current Calibration Load Resistors
HPRS-HIPOT-LOAD
The IET HPRS-Hipot-Load is an excellent replacement for the Fluke 5320A-Load Hipot current calibration load resistors. The IET high power resistive load can be used with the Fluke 5320A Multifunction Electrical Tester Calibrator or standalone. It provides a high power and high voltage load to various hipot tester to create the leakage current needed to calibrate various manufactures hipot testers.
-
product
Waveguide Power Sensor
Make accurate and reliable measurements in the 50 to 110 GHz frequency range. Keysight's waveguide power sensors offer best SWR, high reliability and low loss, and come with a 50 MHz calibration port to reduce measurement uncertainties.
-
product
Air Quality Analysis
Ambient Gas Monitoring: We offer a variety of analyzers for the ambient monitoring of the criteria pollutant gases, including CO, NOX, SO2, and others such as CH4 and CO2. Source Gas Monitoring (Emissions Monitoring): Experience reliable measurement in your process for emissions compliance every time.Ambient Particulate Monitoring: Experience our monitoring technology and gain the power to do more than just inform.Emissions Calibrators: For continuous monitoring of mercury in exhaust stacks, waste incinerators, and cement kilns, or multi-gas models to control the calibration of gas concentrations.
-
product
Dual Display HVAC Clamp Meter w/ Temperature
DL389B
UEi Test & Measurement Instruments
• Dual Display• Input jack locks• Worklight• Backlit display• Auto/manual ranging• Min/Max• Test lead storage• Magnetic mount• User temperature calibration• Auto power off• Degree ºF or ºC• Low battery indicator• Test lead holder on clamp• 2-Year limited warranty
