Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI ARINC 608A Switch Modules
The matrix module is based on our proven BRIC format and can be specified as a 4 or 8 slot module. The module can be fitted with a combination of Resource Distributor and Bus Matrix Input daughter cards as required by the user. The maximum configuration is six Bus Matrix and two Resource Distributor cards fitted in a BRIC8 module.
-
product
Multibus Development and Test Tool for ECUs and Networks
CANoe
The versatile software tool for development, testing and analysis of ECUs and entire networks. Bus systems: CAN, CAN FD, LIN, MOST, FlexRay, Ethernet, WLAN, Car2x ITS G5, AFDX, J1708, ARINC429 > Protocols: TCP/IP, SOME/IP, CANopen, J1939, ISO 11783, J1587, MCnet, GMLAN, K-Line, CANaerospace and ARINC 825. Others upon request.
-
product
PMC Modules
ARINC 429
Sycos range of ARINC 429 PMC modules offer the user up to 32 channels on a single width PMC module. Each channel can be programmed independently to operate at either high or low speed. Firmware options available for Tx Error Insertion and Rx Error Reporting are available.
-
product
Avionics Interfaces & Test Instruments
ARINC 664
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
product
CPCI or PXI MIL1553B & ARINC429 Board
MS 1700
The 1553 Board consists of dual Redundant 1553B Channel A & B and ARINC 429 Channels (6TX and 12RX).
-
product
Multichannel Interface Card
DAS-429mPCIe/RT8-717
The card complies with the PCI Express support one lane 2.5 Gbps PCI Express. The card’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating ARINC 429 and ARINC 717 interfaces and for performing system simulation both in the lab and in the field.
-
product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
MACC - embedded
EXC-8000MACC
The EXC-8000MACC is a table driven translator (data converter - protocol converter) that enables devices supporting different communications specifications (e.g. Ethernet, Serial, ARINC 429, Mil-1553, Discretes etc.) to talk to each other.
-
product
ARINC HSI / ADI Test Fixture
TA-2000
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
product
12" Cable
CONA615-2
A 12" cable transitions from an ARINC 615 Data Loader Cable Connector (JT01RE-18A-53S) to an ARINC 603 Airborne Computer Connector (MS24266R-18B-31P)
-
product
Time-Triggered Ethernet / ARINC 664 Part 7 (AFDX®) / IEEE 802.3 Ethernet Deterministic Communications
TE2
Module TE2 is one of NAI's latest generation of advanced function Configurable Open Systems Architecture™ (COSA®) compatible modules. The TE2 is a certifiable, single-port, tri-redundant, deterministic Ethernet communications interface module that supports TTTech’s certifiable TTEthernet® End System product consisting of three traffic classes: SAE AS6802 (Time-Triggered Ethernet), ARINC 664 Part 7 (Avionics Full-Duplex Switched Ethernet (AFDX®), and/or IEEE 802.3 best-effort protocol. By supporting all three traffic classes, NAI's TE2 is the ideal solution for current users of IEEE 802.3 Ethernet, who plan to upgrade to Deterministic Ethernet (ARINC 664 Part 7 (AFDX®) or Time-Triggered Ethernet SAE AS6802) protocols in the future at any time without changing hardware.
-
product
Data Loading Products
TechSAT's data loading products are available to support all standard ARINC data loading protocols: ARINC 615/615A/826/844 for ARINC 429 and Ethernet based data loading. For next generation aircraft, TechSAT's data loading solutions bring portability to data loading over the new generation of avionics bus and network types: AFDX®/ARINC 664, Avionic & Deterministic Ethernet, TTP, and ARINC 825/CAN
-
product
AC Calibration Standard
1U647-001
The 1U647-001 is a low cost calibration standard used to determine if a 1U632-100 or a 1U663-100 DMU requires factory calibration. Its portability makes it ideal for field-testing. The standard generates signals that simulate the aircraft’s resolvers, rotary variable transformers (RVTs), and linear variable displacement transformers (LVDTs). The unit also generates a pulse width modulated (PWM) signal, and routes the output of an ARINC 429 source to the different DMU input channels. The calibration standard connects directly to the DMU and replaces the output signals of an active extender card. Discrete switch settings simplify testing. The unit is housed in a rugged aluminum case.
-
product
Rugged Embedded Multifunction I/O System with 10 GB Fiber Optic & 1 GB Copper Ethernet Switch
NIU3E
The NIU3E is a small, rugged, low-power, self-contained multifunction I/O processing system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions and incorporates an Ethernet switch module that offers four (4) 10GBase-SR multimode fiber optic ports and sixteen (16) 10/100/1000Base-T Ethernet ports. The NIU3E can also be configured with one smart Configurable Open Systems Architecture™ (COSA®) function module. The NIU3E boasts a Dual or Quad Core ARM A53 processor for customer application and I/O and communications management. The NIU3E is configured with two 10/100/1000Base-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
Interface
RP-708
The RP-708 is a two-channel ARINC 708 weather radar display data bus PMC module interface, supporting variable frame sizes for embedded applications, simulation and test. Abaco Systems provides integrated support for this module on PCI, PCIe, CompactPCI, VME, VXI and native PMC platforms. Each RP-708 channel can be configured as two transmit channels, two receive channels, or one transmit channel and one receive channel simultaneously.
-
product
Application Programming Interface Software
AltaAPI
Alta’s 1553 and ARINC cards include the most advanced Application Programming Interface (API) library tools in the avionics industry, AltaAPI. The API architecture is a properly OSI modeled development package that provides an extremely flexible design to provide quick porting to various operating systems (such as VxWorks 5.X/6.X/7/MILS, Integrity, LynxOS RTOS), Linux 32- and 64-bit, Solaris 10, LabVIEW and 32- and 64-bit Windows 7/8/8.1/10.
-
product
Aerospace and Aviation Solutions
SCOEs and EGSEs by LXinstruments are used during test and validation of satellite assemblies and modules in aerospace applications. As an example, we implemented solar array simulators, battery simulators and high-power load racks for a German satellite manufacturer for testing satellite power supply systems. Due to the high power ratings, the systems are partially equipped with water cooling. Specialized switching modules were developed for switching DC currents at high voltage levels; these can be programmed with SCPI commands via Ethernet.Our modular OTP² functional test platform is ideally suited for implementing durable, reliable test systems, e. g. for in-flight entertainment applications. Since the OTP2 platform is based on open interfaces, it can be quickly and easily adapted to any required communication busses and ARINC interfaces.
-
product
Multi-Protocol & Avionics I/O
We offer high performance, flexible, interfaces to ARINC 429, ARINC 708, ARINC 717, MIL-STD-1553 and others for a range of hosts.
-
product
ARINC 818 Monitor
ARINC 818 Monitor is a rugged display module, powered by High-Performance FPGA to accept various ARINC 818 line rates up to FC 4x and display the converted video data on the monitor of various ICD Specification with very low latency. It supports any progressive video up to Full HD @60fps. These monitors empower pilots to organize and visualize the key information they need.
-
product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote Terminal or a Bus Monitor. This module qualifies for airborne applications.M4K1553Px (Multi Function) This module operates as a Bus Controller, up to 32 Remote Terminals and as a Bus Monitor. Supports an Internal Concurrent Monitor in RT and BC/RT modes.M4K1553Px(S)-1760 Same as M4K1553Px(S) plus MIL-STD-1760 options.M4KMMSI Mini Munitions Store Interface module. Supports RT, BC/Concurrent-RT/Concurrent Monitor and Bus Monitor modes. Up to 8 hub ports EBR-1553 [10 Mbps 1553 protocol using RS-485 transceivers] and 1 monitor output.M4KH009 Based on our H009 family. This module operates as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation.M4K429RTx Based on our ARINC 429RxTx board. This module supports either five or ten ARINC 429 channels each of which can be configured in real time as a receive or transmit channel.M4K708 This module supports two channels of ARINC 708/453, each one selectable as either transmit or receive.M4KSerial This module supports up to 4 independent channels of serial communications, each of which can be selected as RS485, RS422 or RS232.M4KDiscrete This module supports 20 selectable input/open collector output discretes. The module supports TTL (0 to 5 volts) or avionics (0 to 32 volts) voltage levels.M4KCAN This module supports up to 6 independent channels of CAN 2.0B protocol with standard and extended message frames and message identifiers.
-
product
PXIe Avionics Interface Cards
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
product
ARINC 664 Part 7 Test & Simulation Interface for PCI Express
PCIe-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Video and Protocol Analyzer
The Video and Protocol Analyzer (VPA) verifies compliance of designs against the ARINC 818 standard. The VPA software and interface accurately and efficiently decode and display data and flag errors. Multi Stream is a new standard feature of the VPA, empowering it to tackle ARINC 818 interfaces with multiple embedded streams of high-speed video.
-
product
Universal ARINC HSI Test System
TA-1000
This is our ARINC Standard Universal HSI Tester designed to provide a full range of capabilities that allow testing most any HSI you will see come through your shop.
-
product
PXI Interface Module, AIT ARINC 429
M3407A
Interface to the LRU in avionics test solution 4, 8, 16, or 32 software programmable Tx/Rx channels with full error injection/detection Programmable high/low speed operation Real-time recording and post analysis of multiple channels Concurrent operation of all Tx/Rx channels PXI triggers, star trigger, and PXI 10 MHz clock
-
product
PMC Basic Protocol Tx and Bus Monitor
Sy629PMC-BPM
The Sy629PMC-BPM card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory.
-
product
Software
Alta may have the most advanced COTS MIL-STD-1553 and ARINC hardware devices, and our test and development software is 2nd to none. Alta's software is modular, portable, and made for real-time controls & test -- and designed for rapid integration success. This page provides a brief overview of each product and links to main landings pages.
-
product
ARINC PC/104-Plus Interface Card
PC104P-A429
Alta Data Technologies’ PC104P-A429 interface module offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal.
-
product
ARINC interface
RAR-EC
Available in a range of configurations to match your needs, the 11 channel RAR-EC provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected 2-wire, 32-bit protocols, for an ExpressCard interface. The RAR-EC supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, time-tagging, error detection and four avionics-level I/O discretes.
-
product
Interface
RCNIC-A2PAX
The RCNIC platform is a high performance, PCI module (PMC on carrier card) for the AFDX / ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
product
SWaP Optimized Processing and Multifunction I/O & Communications System
NIU3A
The NIU3A is a small, rugged, low-power, self-contained processing and multifunction I/O system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions. The NIU3A can also be configured with up to three smart Configurable Open Systems Architecture™ (COSA®) function modules. The NIU3A boasts Dual or Quad Core ARM Cortex®-A53 processors for customer software applications and I/O and communications management. The NIU3A is configured with two 10/100/1000BASE-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3A delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
