Filter Results By:
Products
Applications
Manufacturers
IC Clips
Connect over the top of most chip formats contacting each chip lead.
See Also: IC, Clips, Digital IC Testers, IC Test, IC Probes
- TEAM SOLUTIONS, INC.
product
IEEE-488 GPIB Device Interface IC (Chip) for the PCI-Bus
GPIB-72120
The i72120 GPIB-Chip is the ideal solution to implement a IEEE488.2 GPIB interface for next generation PCI based instruments. The GPIB-ASIC is designed to meet all of the functional requirements for talker and listener (TL) devices as specified by the IEEE Standards 488.1-1987 and 488.2-1987. Connected between the PCI bus and the GPIB, this GPIB-IC provides high-level management of the GPIB to unburden the processor and to simplify both hardware and software design. The i72120 is fully compatible with the PCI specification and requires only the addition of bus driver/receiver components to implement a talker/listener GPIB interface.
-
product
Digital Incircuit Test
PFL780/760
The PFL780 and 760 use IC clips as a test interface. This makes them ideal for the service and maintenance of legacy systems. If you need to work on high density surface mount PCBs you should consider the GRS500 as a more suitable alternative.
-
product
Dip Clip, 16 Pin With Nickel Silver Contacts
3916A
Dip Clip, 16 pin with Nickel Silver contacts. Pomona DIP Clip® test clips are designed for testing dual-in-line IC packages on PC boards. These devices incorporate many built-in features that assure a positive electrical connection as well as hands free testing.
-
product
Quad Flat Pack IC Clip Pair (Yellow/Green) (Qty.1 Pair)
PK-ZS-025
Quad Flat Pack IC Clip Pair (Yellow/Green) (Qty.1 Pair)
-
product
Surface Mount-to-DIP JEDEC SOT-25, SOT-23A-6 Adaptor
1110748
Surface Mount to DIP Adapter for SOT-25, SOT-23A-6. Allows for breadboarding or substitution of microgate SOT-23A-6 and SOT-25 IC and transistor packages into .100 [2.54] pitch proto boards or PC boards. Solder masked top-side pads allow user to hand solder devices directly to topside of adapter with fewer problems of solder bridging. Longer male bottom pins are available at special request for easy use of probe clips. Large topside pads allow for soldering test pins, jumpers, etc. to top of adapter.
-
product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
product
Kelvin IC Clip Lead
16089C
Measure odd-shaped components that you cannot measure using conventional fixtures
-
product
Inbuilt External Controller ATE with Touch Screen Features
QT 200NXT
Qmax Test Technologies Pvt. Ltd.
QT 200 nxT is a ultra modern stylish Inbuilt external controller ATE with touch screen features, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software. The vast library support helps you to functionally test host of different IC families. Other features like user-friendly Windows based software, add-on utilities like oscilloscope, RCV meter circuit tracer, etc. makes it a favorite and makes very effective for repairing PCBs without schematic/ circuit diagrams. All these tests are carried out using simple BUT Interface like multipin test clips, probes or custom test fixture
-
product
Dip Clip, 14 Pin With Nickel Silver Contacts
5014
Pomona DIP Clip test clips are designed fortesting dual-in-line IC packages on PC boards. Thesedevices incorporate many built-in features that assurea positive electrical connection as well as hands freetesting.
-
product
IC Test Clips
Low-profile fine-pitch chips, desnely populated boards, or vertical boards, Pomona test clips connect you with confidence.
-
product
Pin Point Range Systems
The PinPoint Alpha system is a flexible, adaptable and modular PCB and IC fault finding system, which allows you to apply different electronic test methods to obtain maximum test coverage and fault detection. Test signals can be applied at the PCB edge connector or through test clips and DTIs to perform fixtureless in-circuit testing.
-
product
Dip Clip, 14 Pin With Nickel Silver Contacts
5114
Pomona DIP Clip? test clips are designed fortesting dual-in-line IC packages on PC boards. Thesedevices incorporate many built-in features that assurea positive electrical connection as well as hands freetesting.
-
product
Test Clips
Angled Nose allows tight hold on 66 blockUse on 110 block with jumper and bed of nailsUse on larger cables with single piercing nail
-
product
Miniature IC Handler
3270
Chroma 3620 is an innovative system handler for high-volume multi-site IC testing, especially for CIS Testing, at the system level.
-
product
IC Test Services
With knowledge gathered from decades of supporting Tier 1 and emerging industry leaders, Amkor understands test solutions must address advanced technology, quality, performance and cost of test. We offer full turnkey solutions including wafer processing, advanced bump, wafer probe, assembly, final test, system-level test, burn-in and end-of-line services.
-
product
IC Design & Verification
Mentor Graphics provides best-in-class products for IC design. Calibre for physical verification, extraction, resolution enhancement and mask data preparation, ADVance MS for analog/mixed-signal simulation and an integrated tool flow for custom IC design
-
product
Kelvin Clip Set
11062A
Create custom Kelvin probes for 4-wire resistance measurements; set contains only the two gold-plated clips
-
product
Large Kelvin Clip Lead
16089A
Measure odd-shaped components that you cannot measure using conventional fixtures
-
product
Photocouplers/Optocouplers IC Output
The PS8xxx/PS9xxx series, a range of IC output type photocouplers (optocouplers), feature a high-speed response from 1Mbps to 15Mbps and a wide variety of DIP and SOP packages that can be surface mounted (SMD).
-
product
Scientifically Calibrated Audio Clips
AudioRef™
AudioRef is a package of scientifically calibrated audio reference clips that enable professionals to accurately set up and evaluate audio monitoring equipment.
-
product
Counterfeit IC Detector
Sentry
The ABI SENTRY is a unique solution for the quick and easy detection of Counterfeit ICs and components. ABI Electronics has over 27 years of experience in the field of Test & Measurement equipment as well as Contract Electronics Manufacturing. Knowledge of both industries has allowed ABI to design this product around two main concepts:
-
product
Compact Professional IC Tester
ChipMaster
The ABI ChipMaster Compact Professional is a low-cost, hand-held out-of-circuit IC tester. The ChipMaster is designed for testing digital ICs with up to 40 pins through a ZIF socket (see LinearMaster for analogue devices). A range of adapters is also available for SOIC and PLCC devices.
-
-
product
IC Tester
The Peritec adopted the NI products, to build in 1/10 the cost of the commercial product functions of the IC tester. It offers original brand as "ECOIC".IC tester on the market, yet very expensive that several tens of million, part of its function could only really used. Therefore, it possible to continue to build the only really necessary function in Peritec, we have created a mechanism to be completed at a lower cost and development, high-performance, short-term.
-
product
IC Product Testing & Analysis Services
Integrated Service Technology
Integrated Service Technology Inc.
iST (Integrated Service Technology Inc.) is a leading lab-service company, specializing in the development of IC product testing & analysis, failure analysis, debugging, reliability test, material analysis. Apart from developing testing technologies for the upstream IC design and semiconductor industries, iST also expanded to provide a full-spectrum of services for the mid and downstream companies in the electronics industry.
-
-
-
product
Xhorse Eeprom Clip
You need to choose the right type of eeprom with the & quot CLIP & quot In the set:
-
product
Mag Lead w/Alligator Clips
138
*54" Test Lead Set *Mag Lead features a magnetic disconnect. *You can "stick" to any metallic ground or test point. *Time saving product - can substitute for alligator clips at metallic test points. *Now, when you need alligator clips, you've got them! *Fits almost all DMM's and hand held scopes. *Get the Mag Lead, it stays put and won't fall off!
-
product
Alligator Clips
U1162A
Pair these insulated alligator clips with Keysight standard test leads
-
product
24 In. 8-Way Alligator Clips To RJ45
#TCA015
24 inch cable assembly 8-Way alligator clips to RJ45, 849160008392
