Filter Results By:
Products
Applications
Manufacturers
- Scientific Test, Inc.
product
Automated Discrete Semiconductor Tester (ATE)
5300HX
The Model 5300HX Automated Discrete Semiconductor Tester (ATE) is designed for fast, reliable testing of a wide range of discrete devices. Using an on-board Intel SBC, can provide stand alone testing capability or connected to a PC for intuitive test development and data capture.
-
product
Rugged Igniter Tester
4314 KV
Model 4314 KV is a 4-wire ohmmeter designed to use low test currents for its measurement. Additional circuitry proprietary to Valhalla Scientific is used to ensure that test current levels do not exceed the specified “fail-safe current” even in a worst-case component failure situation.
-
product
Arc/LED Lighting Testers
This system is a modern replacement for an obsolete product tester. This tester Hipots the lamp under test, checks for proper operation at the required voltage and also detects short circuit operation and the 5KV ignitor pulse signal. This tester allows for quick calibration to permit traceable/repeatable results and store the test results for product tracking.
-
product
Digital Igniter Tester
Alpha 4314KRC
The Alpha 4314 Digital Igniter Tester is a portable digital ohmmeter which has been specifically designed for ultra-safe resistance testing on explosive devices (i.e. squibs, detonators).
-
product
Digital Igniter Tester
Alpha 4314KRC
The Alpha 4314KRC Digital Igniter Tester packaged per NSN 6625-01-460-1499.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
Digital Igniter Tester
Alpha 4314
The Alpha 4314 Digital Igniter Tester is a portable digital ohmmeter which has been specifically designed for ultra-safe resistance testing on explosive devices (i.e. squibs, detonators).
-
product
Low Power Ohm Meter
LRO-20
Laxtronics Instruments & Controls Pvt. Ltd
LOW POWER OHM METER / DIGITAL IGNITER TESTER (0 - 19.99Ω)
-
product
Rugged Igniter Tester With Current Monitor And Single Connection For Measurement And Charging
4314 KVM
The Valhalla Scientific Model 4314 KVM Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
Igniter Tester
A specific type of ohmmeter used to conduct safe resistance tests on explosive devices, such as squibs.
-
product
Igniter Testers
Igniter Tester is a failsafe and portable digital ohmmeter specifically designed for ultra-safe resistance testing on squibs, flares, bridge-wire, and other explosive devices. The 620A-4 ohmmeter has been approved by the USAF Non-Nuclear Munitions Safety Board for usage on all non-nuclear munitions, and independently certified to meet Mil. Std. 810 Mtd. 511 for usage in fuel-filled environments. Due to its intense self-safety design and numerous certifications, the 620A-4 failsafe ohmmeter is the industry standard for military programs in need of igniter testing.
-
product
4314-Ki Wide-Range, Ultra-Safe Digital Igniter Tester
Featuring the intrinsically-safe internal circuitry of our storied 4314 igniter tester line, the 4314Ki begins the next generation of precision measurement instruments.
-
product
Wide-Range Digital Igniter Tester
4314Mi
Featuring the intrinsically-safe internal circuitry of our storied 4314 igniter tester line, the 4314Mi is the newest addition to Valhalla Scientific's i-Series Wide Range Igniter Testers.
-
product
PAM4 Bit Error Rate Tester.
BERT-1102
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Hardness Tester
Shenzhen Graigar Technology Co.,Ltd.
Hardness Testing. Hardness is a characteristic of a material, not a fundamental physical property. It is defined as the resistance to indentation, and it is determined by measuring the permanent depth of the indentation.
-
product
Franklin Tester
Model 717
The Model 717 Franklin Tester provides a means of testing single strips or punchings of flat rolled electrical steel, for surface insulation resistance under predetermined conditions of voltage and pressure.
-
product
Coil Tester
It is a new impulse winding tester that incorporates high precision, a wide range of functions, various expandability, improved operability, and a full range of external communication interfaces.
-
product
Battery Testers
Wuxi IMHOO Technology Co., Ltd.
Voltage of batteryBattery type1.5VButton Cell, AA,AAA,C,D,N3V Lithium6V Camera Battery9V 12V 15V 22.5V Power Source Not use batteryWeight 260gmeasurement 100x63x33mmPacking50pcs/CTN
-
product
Automated Tester
With high labor costs in Europe and the US, and the surge in labor cost in Asia, automated test solutions are in demand. Automated systems also improve traceability and reduce operator mistakes.The combination of automation with high throughput test systems is perfect to extend the usage of Flying Probe Testers to mid size production/sample volumes.
-
product
CDM Tester
Tokyo Electronics Trading Co., Ltd.
Determine what level of CDM discharge causes device damage by placing the device package on a metal plate with the pins facing up.
-
product
EMC Testers
The KES7000 System is a conductive immunity test system that is fully compliant with ISO7637-2 and ISO7637-3, international standards for EMC testing required for automotive electronic components. This system consists of the KES7700 Series Transient Surge Tester, KES7400A Series Voltage variation simulator and KES7100 application software dedicated to the KES7000 system. This product configuration supports JASO standards and the special test requirements of car manufacturers with options or custom orders.
-
product
RX Tester
FC5000 Series
The Aceco FC5001 is a two-way FM radio tester that has the ability to lock automatically and almost instantly on to any FM signal within its frequency range. FM signals are demodulated and output it through its internal speaker or external earphone. The high sensitivity to nearfild signals makes it ideal for RF security, counter-surveillance and radio communication testing applications. Supplied as a complete with internal NiCd pack, AC wall charger, VHF/UHF flexible antenna and audio earphone.
-
product
Handover Tester
Qosmotec Software Solutions GmbH
The QPER Handover Tester provides engineers with a platform to test all relevant signal strength effects on the radio channel.
-
product
Voltage/Continuity Tester
VOT-52
Standard Electric Works Co., Ltd
● Voltage test: 12V to 1000V AC/DC (8 LEDs) with indication by buzzer.● Voltage range: 12V, 24V, 50V, 120V, 230V, 400V, 750V, 1000V.● Test leads positioned at 19mm apart.● Interchangeable probe tip for 2mm and 4mm.● Polarity test : LED +/-● Audible continuity test.● Phase rotation test : /● Self-test button to ensure proper function of the device prior to testing.● Waterproof design, protection class: IP65.● Phase / Neutral identification.● Rubberized double-molded housing.● ELCB / RCD trip test.● Flashlight function.● Safety standard : IEC/EN 61010-1 III 1000V IEC/EN 61010-1 IV 600V IEC/EN 61243-3 EN 61326-1
-
product
Bump Tester
KD-163
King Design Industrial Co., Ltd.
*Comply with IEC-68-2-29 testing specification(10g/ 16ms、15g/6ms、 40g/6ms、100g/2ms).*Easy installation and simple operation; Low noise; no maintenance required; function holds long.*Well-designed and no resonant-structure, air anti- vibration pad can effectively isolate floor vibration.*Accelerometer adopts repeated measurement and adjustable half-sine wave generator; to control the data is precise.*Magnesium alloy platform is anodized, Servo motor cam to drive, and can adjust the frequency automatically.*The adjustable acceleration value and shock domain is patent design (1ms-13ms).
-
product
Relay Tester
LET-4000-R
Regulation and Measurement Module performs the regulation of the DC current and is made with a variable auto transformer (Variac) regulating a three phase DC current, with a power of 8KVA and a three phase transformer of 8KVA with 2V nominal power in the secondary windings. A built-in ammeter and a timer give the information of the current injected and the operation time of the relay under test.
