Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 395kΩ
50-298-142
The 50-298-142 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
CompactPCI Interface Card
CPCIC-1553/PXI
The CPCIC-1553/PXI Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Our Card and Software Packages are Designed for Fast, Portable Integrations. The CPCIC-1553 is the Only Commercial Off the Shelf (COTS) Card that Passes and Executes the SAE AS4111/4112 Protocol Tests.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm
50-294-023
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
High Speed DAQ Card
With 25 MS/s, 100 MS/s or 250 MS/s the high speed input cards are suitable for the acquisition of ultra fast, accurate and high resolution transient signals in high speed mechanical tests or electrical/electronic environments. 14-/15-/16-bit resolution; dynamic resolution increase. available 5/18
-
product
Intelligent Interface Card
IIB-1553-MMA
The IIB-1553-MMA is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the M-Module standard, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-MMA supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, withcomprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
product
Smart Network Emulation for All Mobile Device Tests
CMWcards
Use R&S®CMWcards to prepare the tests you always wanted, but never found the time to set up. Create wireless signaling and application tests on the R&S®CMW500 wideband radio communication tester just by setting up a hand of cards – no programming required. Revolutionary card wizards and unique game rules guide you through setting up test sequences that fully comply with test specifications. Thanks to the R&S®CMW500 tester’s unrivaled multi-technology capability, R&S®CMWcards can be used to rapidly reproduce signaling scenarios for various wireless communications standards.
-
product
PXI - Test System
We provide a complete PXI test system made by PXI individual components: 19'' rack, Measuring and stimuli cards, Relay cards, Power Supplies, Integration additional protocol cards such as CAN and CANopen, Boundary Scan, Integration of additional test hardware
-
product
Microwave Switches
SMX-7XXX (Microwave)
The AMETEK VTI Instruments SMX-7000 Series of microwave switch cards extends functionality typically reserved for dedicated stand-alone systems into the PXIe from-factor. Single and dual slot configurations provide the ability to mix and match multiple switch configurations including SPDT, SP4T, SP6T and Transfer. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers. Ideally suited for medium-to-high density automated test equipment (ATE), the SMX-7000 Series deliver uncompromised measurement integrity ideal for the most demanding aerospace, defense and communication applications.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 201kΩ
50-298-041
The 50-298-041 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 201kΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm With SPDT
50-293-123
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
64-bit/66 MHz Metering PMC-to-PMC Extender
3954
The extender/analysis probe permits extension of a PMC card beyong the edge of a host processor front panel, providing access to both Side 1 and Side 2 of a PMC under test.
-
product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781420-17
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781421-11
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
FPGA PXI Card with 40 Channel ECL Buffer Module
GX3640
The GX3640 is comprised of the GX3500 FPGA card and the GX3540, 40 channel ECL expansion card. It is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), and functional test applications. The GX3640 consists of 20 differential ECL drivers and 20 differential ECL receivers. Each channel can be accessed via software commands for use in static I/O applications.
-
product
PCIe 4.0 Protocol Analyzer
Summit T48
Teledyne LeCroy’s Summit™ T48 joins the Summit™ T416 as the second protocol analyzer to be released in its family of tools supporting the PCIe 4.0 architecture. The new Summit™ T48 protocol analyzer based on the PCIe 4.0 specification supports up to 16GT/s and up to x8 lane width for protocol analysis. Companies that are interested in testing PCIe 4.0 based I/O cards such as Storage Controllers, Ethernet, Fibre Channel, Infiniband, and others will now be able to get all of the protocol analyzer debugging features they need, while being able to better manage their costs. SSD storage applications will also benefit from the integrated support for SSD bus protocols such as PCIe/ NVMe/ SMBus/ NVMe-MI/ TCG and others. When combined with Teledyne LeCroy’s Summit™ Z416 protocol exerciser, the Summit™ T48 will provide a deeper understanding of test results on a variety of test configurations. Teledyne LeCroy’s wide range of high speed interposers and probes provide full flexibility and connectivity to CEM and other form factor sockets on system boards as well as solder down and mid-bus probes.
-
product
6 Channel Function Generator / Flow Simulator
DP-cPCI-2601
DP-cPCI-2601 is a 6 Channel 2MS/s Waveform Generator with high frequency performance, versatility and compact size in an economical cPCI bus format. Signal output in the range of 10 mHz to 5 KHz with 14 bit vertical resolution makes this single slot, 6U-sized cPCI card a powerful solution to meet most demanding test stimulus.DP-cPCI-2601 uses Direct Digital Synthesis (DDS) technique to generate stable and accurate output waveforms down to 0.01 Hz resolution. DP-cPCI-2601 offers Sine, Square, Ramp, Triangle, Pulse as built-in wave shapes and user defined arbitrary waveform.DP-cPCI-2601 can frequency sweep any of its function outputs. User can sweep upwards using linear sweeps.
-
product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-14
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781420-33
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Cost-Effective ATE System
PRO RACK ATE
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
product
Low-leakage Switch Matrix Family
Conducting all the parametric measurements necessary for the numerous test structures on a semiconductor wafer can be a time-consuming and expensive process. With the cost of end-user devices continuing to drop, even laboratory characterization environments must reduce the cost of test. Until now engineers and scientists working on current and future semiconductor process technologies were faced with a difficult choice: either use a semiconductor parameter analyzer with positioners on a wafer prober, which limits the ability to perform automated test, or use a switching matrix and probe card, which reduced the analyzer's measurement resolution. Utilizing a switching matrix with a semi-automatic or fully-automatic wafer prober enables characterization tests to be automated, eliminating the need to have an operator manually reposition the probes each time a new module needs to be tested. This reduces both test time and cost. Due to the many price/performance points available, Keysight's switching matrix solutions provide the flexibility to choose exactly what your testing needs require, without overspending.
-
product
Remote Display Kit for Post.4d
postrd
remote display kit for post4d, not RoHS compliant (can be considered test equipment, not subject to RoHS). Connects to PC Engines post4d PCI POST card (will not work with post2b or post5a). 20 inch cable, place display in a more accessible location. Ideal for software development or test fixtures.
-
product
In-Service Electrical Continuity Test Card
Cisco ONS 15454
The Cisco ONS 15454 In-service Electrical Continuity Test Card is a solution for confirming proper DS-1 and DS-3/EC-1 cabling between the Cisco ONS 15454 shelf assembly electrical interface adapter (EIA) panels and the user's patch panels. The solution is designed for shelf installations that are presently carrying traffic and tests for common wiring errors including electrical shorts, opens, wrong connections, and tip/ring reversals.
-
product
FCB Probe Card
The FCB Probe Card is the most mature technology of buckling beam probe card. It is aimed to achieve the semiconductor ship manufacture time-to-market (TTM) and cost of test (COT) demand. FCB is a proven solution for a variety of semiconductor production tests from early engineering pilot-runs to high volume manufacturing (HVM). FCB is ready for device requiring high signal integrity probing (SI) and/or power integrity probing (PI). Applications include cutting-edge SiPs/SoCs, WLP, graphic processors, micro processor, industrial microcontrollers, and more. FCB guarantees the world’s best overall cost-of-ownership (COO) for various DUT applications.
-
product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 472Ω
50-298-120
The 50-298-120 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm - SPST
50-294-123
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm
50-293-014
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Device Power Supply - 4 Isolated Channels, 20-bit Measurement Resolution
52310e series
Chroma 52310e Series i s a programmabl e PXI-Express DPS (Device Power Supply) Card designed for high-accuracy and reliable output power for device test applications. Its compact size, easy level of integration, and high flexibility make the 52310e Series ideal for multi-channel power supplies. Chroma 52310e Series features 8 selectable control bandwidths to ensure high speed output and stable operation; multiple current measurement ranges with a 20-bit DAC/ADC provide the highest resolution and accuracy with a sampling rate up to 600K S/sec; programmable internal series resistance for battery simulation. Chroma 52310e DPS series has a patented hardware sequence engine that has deterministic t iming to cont rol each DPS channel. The sequencer's on-board memory can store up to 1024 sequencer commands and 32k measurement samples per channel.
-
product
PCI Resistor Card 2-Channel 2 Ohm To 65.5k Ohm
50-293-033
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
IoT Tester for Cellular & Non-Cellular Technologies
CMW290
The R&S®CMW290 is the ideal test solution for the integrated wireless communications modules used in laptops, data cards, wearables and various IoT products. The R&S®CMW290 offers functions tailored to these applications within the R&S®CMW product family. The tester provides network emulation (signaling mode) as well as generator and analyzer functions for the supported cellular and non-cellular standards including GNSS and broadcast technologies.
-
product
12-Slot PXI chassis
PXCe4012
The PXI chassis of the PXC family are very space-saving, since the measuring cards are installed horizontally instead of vertically in contrast to the usual PXI chassis. Instead of the usual 4-6 U, only 1/2 U are required in the test system.
-
product
Dynamic Digital I/O with Per Channel Programmable Logic Levels and PMU PXI Card
GX5295
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
