- Frequency Devices Inc.
product
Bench Top and Rack Mount Instruments
AC powered, front panel tunable LP or HP, 8p filter and gain
-
product
19-Slot 3U PXI Chassis with AC
PXIS-2719A
The ADLINK PXIS-2719A is a 3U PXI chassis with a series of advanced features:*An innovative cooling mechanism to deliver efficient and uniform heat dissipation*Superior stability within an extended temperature range*Intelligent chassis management that dynamically monitors and manages fan speed, system voltages, and internal temperature*Remote management via standard RS-232 monitoring port
-
product
Test Analyzer
ST2303
Shenzhen Star Instrument Co., Ltd.
The ST2303 three-phase energy meter field test analyzer reaches accuracy class 0.05. It generates stable signals by using ARM and digital signal processing technologies. Its highlights include compactness, light weight and portability. Various supply options, including measuring circuit, external AC power supply and internal lithium battery are offered.
-
product
PXI 5A MUX, 1-Bank, 48-Chan, Ind. Isolation
40-651-101
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
1000W, 1500W HSM Watt Power Supply Models
Series HSM
The Kepco HSM series comprises a group of ten models, seven 1000 watt power supplies with outputs from 3.3 volts to 125 volts and three 1500 watt power supplies with outputs from 24 to 125 volts. All models feature current sharing for parallel operation and redundancy applications. Kepco¹s 1000W HSM have a wide-range input (90-277V a-c). The 1500W models operate 180-277V a-c. Both incorporate power factor correction to meet EN 60555-2 and EN 61000-3-2. These modern power supplies operate at 100KHz using current mode control to provide rapid response to source and load changes and tight stabilization.
-
product
Micsig Ocilloscope AC Current Probe
ACP1000
Shenzhen Micsig Instruments Co., Ltd.
*Test Current Range: 0.1A-1000A*Operating Frequency: 10Hz-100kHz*Maximum Primary Current: 2000A (2s)*Output Signal: mV/A*Highest Precision: 1%
-
product
Power RC Snubbers
Single phase and Three phase availableSuitable for AC and DC voltage applicationResistance and rate power of Resistor : 1 - 50W ( can be customized to 100W or above )Voltage: 63Vac, 125Vac, 280Vac, 480Vac, 500Vac, 600VacOperating temperature : -25~+85C / -40~+105CTesting Voltage : : 1.5 x Un 10sec ( can be customized )Varistor and Diode options available. Different applications can have very different electrical and mechanical profile requirements.Please feel free to send your application details for a suggestion and quotation.
-
product
Digital (1kV below) Insulation Tester
1160 IN
Standard Electric Works Co., Ltd
● Measures insulation (MΩ), Continuity (Ω) and AC voltage.● Three insulation test voltages(DC V) : 250V, 500V, 1000V.● 3½ digital LCD (2000 counts).● 68 × 34mm ( 2.677” × 1.338” ) large LCD display.● LCD backlight display.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA load.● 200mA short circuit testing current for continuity.● Auto ranging.● Fuse protection.● Data hold function.● BS 16 edition.
-
product
SCR Controlled DC power Supplies
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single-phase or three phases. With single-phase AC input, the DC output ripple is very high (50%). With three-phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three-phase AC input instead of a single phase.
-
product
PXI Single 6-Channel 30A Solid State MUX
40-667-012
The 40-667 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 30A of continuous current and switch up to 40V signals. The switches can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Optical-Electrical Converter - PXI
O2E 1000 – 1400 Series
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
10 Channel ADC FMC Module
ADCFN10-DC – HPC
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN10 is a ten channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Both AC and DC coupled input are supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
product
Analogue (1kV below) Insulation Tester
1652 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 3Ω & 500Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.●...show more -
product
DC-Powered, AC Voltage Monitor
VAD/VQD
NAI’s VAD and VQD are DC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
product
LED Synchroscope
LS-96 SYNC
Standard Electric Works Co., Ltd
● Input Voltage : 110V AC, 120V AC, 220V AC, 230V AC or 240V AC.● Square shape panel 96 x 96mm● 3 bi-colored LED indicators for "SYNC", "GEN" and "BUS"● 24 LEDs in a circle display the phase angle and the frequency differences between 2 networks● 360° indication● 12 o'clock position LED is bi-colored● PC window, ABS resin frame, PC case
-
product
Fully Automatic Transformer Winding Resistance Tester
Measure DC resistance of transformers windings etc. Introduction: The NMC ''TDR'' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. ''TDR'' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. ''TDR'' is powered by 220V AC mains single phase supply. The meas...show more -
product
600 Amp DC / 400 Amp AC Current Probe
DC600
Can measure from 5 to 600 Amps DC current for most industrial DC measurement jobsNo batteries required, because power is supplied by PowerSight. This means that the probe will not stop during a long monitoring session.
-
product
Radio Module (2x2)
SX-PCEAC2
The SX-PCEAC2 is powered by Qualcomm Atheros radio chip, the QCA6174-5, which features 2x2 wave 2 MU-MIMO technology. It is a dual-band 802.11 a/b/g/n/ac module with Bluetooth support which is designed for devices that require wireless connectivity in a small form factor combined with high performance with throughputs reaching up to 867Mbps.
-
product
AC Power Sources
CS Series
AMETEK Programmable Power, Inc.
The CS Series represents an advanced AC current source that addresses increasing demands on manufacturers to test products using real-world current profiles. By combining true current transconductance amplifiers with an advanced digital controller and harmonic power analyzer, CS Series current sources are capable of performing tests that would traditionally have been difficult to accomplish.
-
product
Battery Electrical System Analyser
We invented the “Resistance method” which uses a series of shorting pulse to measure the voltage drop in order to calculate the plate’s internal resistance. Unlike other patented “Conductance method” which generates an AC pulse across the battery terminal to measure impedance.
-
product
Muffle Furnace
K585
Chongqing Kailian Yongrun Industrial Co.,Ltd.
Heating elements: MoSi2, SiC, Resistance wireWorking voltage: AC 220V, Single phase, 60Hz/50Hz(or at your option)Temperature accuracy: 1 degree CelsiusHeating rate: 0 - 15 degrees Celsius/Min (recommend less than 10 degree Celsius)Chamber size: different chamber sizes for your choice.
-
product
HIPOTS (High Voltage Testers) / AC Hipots
5 kV Analog
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Variable from 0-5 kV. Multi-range kV & mA meters. Zero start interlock protection.
-
product
Autoranging Digital Multimeter w/Bargraph
HH2209
High Accuracy (Basic Accuracy 1.0%)Jumbo LCD display 3260 count, 21mm figure heigh with BaragraphAuto Ranging or Manual Ranging at your choiceHigher Voltage test up to AC 750V and DC 1000VHigher Current test up to 20AResistance test up to 30MΩTemperature test range from -4oF or 1832oFWide Frequency test range up to 300kHzDiode test, audible continuity check and Transistor testLow Battery Indication
-
product
12-600V 2-Pole Voltage Tester
1964B
Peaceful Thriving Enterprise Co Ltd
The 2 pole Voltage Tester provides a clear indication of AC or DC voltage levels via bright LED's from 12-600V. It is constructed in accordance with the latest safety standards and is ergonomically designed which is durable enough for both industrial and domestic uses.
-
product
PXI Solid State Multiplexer, Dual 3-Channel, 30 Amp
40-667B-011
The 40-667B-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
AC Ground Bond Tester
446
Our 446 model is a 4-in-1 tester with AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond capabilities. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application. The 446 is equipped with multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Add to user safety by equipping your tester with Personal Protective Equipment (PPE) via the built-in safety interlock.
-
product
AC DC Withstand Voltage & Insulation Tester (HI-POT)
SS71XX series
High voltage withstand and insulation tester (HI-POT tester) is used for testing insulation grade and withstanding voltage capability of electrical equipment, transformers, motor, relays, cables, electronic components, electronic applications, inductors, ignition coils, insulation wires, insulation tapes, valve coils, reactors, contactors, etc.
-
product
Electrical Testers
Precision Mastech Enterprises Co.
AC Voltage range: 50V-1000V AC, 50/60HzSafety standards: Designed to international safety standard IEC61010 - 1/600V CAT III, 1000V CAT II.Battery: 2*1.5V (AAA type)Altitude: <2000mOperating temperature: -10 to 50CStorage temperature: -20 to 60CHumidity: <85% relative humidityDimensions: 157*24*20 mmWeight: Approximately 42g
-
product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
product
PXI 5A Power MUX, 4-Bank, 11-Channel
40-651-003
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
Static Elimination
Fraser Anti-Static Techniques Ltd
Cost-effective passive, AC or 24 V DC technology solutions for static neutralisation, dust removal and cleaning.
