Filter Results By:
Products
Applications
Manufacturers
- Taylor Dynamometer, Inc.
product
Towing Dynamometer
RS-110K
RS-110K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-110K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-110K is designed to maintain 110,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds.
-
product
MBT 7000 Series
Maschinenbau Haldenwang GmbH & Co. KG.
Roller-Brake-Tester up to 18000 kg axle load
-
product
Four-Wheel Drive Single Roller Dynamometer for Cars with Axle Load of 2.4T
MSR 500/3 CAR 4WD | VP 230037
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/3 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/3 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.
-
product
Axle Damping Test Bench
C_MSD S 13.0 W220 | VP 215051
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
product
Axle Damping Test Bench
C_MSD C 13.0 W220 | VP 215050
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD | VP 230036
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
product
Vibration Testers
Application for vibration tester: used for measuring periodic motion, to check the imbalance and deflecting of moving machinery.Is pecifically designed for present measuring various mechanical vibration. So as to provide the data for the quality control, run time and equipment upkeep.use the high-performance acceleration meter, realize the repetitiveness and accurate measurement. it has the function of testing axle bearing situation
-
product
AWD Dynamometers
MD-AWD-500-AC/EC-100/250
The key to designing an AWD dynamometer properly is to understand the methods currently being used by manufacturers in the field of AWD drivetrain technology. A dynamometer that can accommodate various types of AWD vehicle transmissions and wheelbases without excessive complication and, more importantly, without risking damage to a client’s AWD system is paramount. Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under “optimum” operational conditions; whereby torque is distributed to the vehicle’s tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency. To achieve this, Mustang’s AWD-500 Series incorporates an internal drive system that synchronizes the front and back rollers to simulate a flat, dry road condition. Synchronization, or linkage, insures that the front and rear rollers are always spinning at precisely the same road speed. This process eliminates the possibility of activating a vehicle’s traction control system and also insures that a vehicle’s torque management system is operating under the assumption that the vehicle is not skidding, turning or slipping. Mustang’s AWD-500 can be operated in AWD Mode while testing two-wheel drive vehicles. This process allows the non-driven axle to be spun by the dynamometer rollers at the same speed as the driven axle, eliminating the speed differential that occurs on two-wheel drive dynamometers – problem solved.
-
product
Mechanically linked AWD Performance Dyno
Mustang''s AWD-500 can be operated in AWD Mode while testing two-wheel drive vehicles. This process allows the non-driven axle to be spun by the dynamometer rollers at the same speed as the driven axle, eliminating the speed differential that occurs on two-wheel drive dynamometers problem solved.
-
product
Towing Dynamometer
RS-40K
RS-40K towing dynamometer is designed for testing today’s DOT Vehicles (Classes 5 and 6) which include trucks and buses. The RS-40K is built with a heavy-duty steel frame, industrial axle and rides on an air ride suspension. The RS-40K is designed to maintain 40,000 Newtons of constant drawbar force and the ability to simulate an uphill slope of 25%. The dyno uses eddy current absorbers with special high temperature coils. The power is provided by an industrial generator. Testing is unlimited at lowspeeds.
-
product
Suspension/Road Contact Tester
VLT3673-G6
The VLT 3673-G6 suspension / road contact testers operate according to the well-known EUSAMA principle. However, the diagnostic options are not restricted to the contents of this specification. In addition to the usual road contact values, the following values are also measured and displayed: the contact value difference, resonance frequency and wheel weight at minimum contact value, tyre rigidity, wheel weight and axle weight. There is a general final evaluation so that all these values do not have to be interpreted after every test.
-
product
Vehicle Testing Technology
Maschinenbau Haldenwang GmbH & Co. KG.
Vehicle testing technology includes products for testing axle damping, wheel arches and axle and joint play. Diagnostic devices for eg the sound level or clamping force also make their contribution to the targeted assessment of the vehicle condition.
-
product
920 HP AC Chassis Dynamometer
TD-36-AC
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 39,400 lb (17,872 kg)Capacity: 920 hp at 40 mph (686 kW at 64 kph)Rolls: 36 by 31 in. (915 by 787 mm) 4 fixed rolls to accommodate axle spreads from 48 to 74 in (1,219 to 1,880 mm) tandem centersPit Required Depth: 35 in. (889 mm)
-
product
Towing Dynamometer
RS-200K
RS-200K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-200K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-200K is designed to maintain 200,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are nolead-acid batteries to charge and testing is unlimited at low speeds.
-
product
Brake Test Systems
GIANT 9000 Series
The major test target is to detect noise and vibrations generated by the vehicles brake. Our intention was to build a dynamometer that can operate either with brakes mounted to the complete vehicle, or with just the axle module mounted to a universal adaptor system or wheel suspensions.
-
product
Super MUTT Deluxe Edition Electrical Circuit Tester
#9008-DL
Innovative Products of America
The Super MUTT places a load on the trailer's electrical circuits to identify wiring problems while providing remote control operation over both air brakes and lights. Built to facilitate a one-man testing operation, the Super MUTT reduces guesswork and inspection time to prevent failures that lead to expensive road calls and citations. The remote control allows for repetitive air brake actuation at each axle to reveal developing problems often missed by normal testing procedures.
-
product
Tachometer Tester
Maschinenbau Haldenwang GmbH & Co. KG.
for motorcycles, for cars and vans up to 4000 kg and for cars and trucks up to 13000 kg axle load.
-
product
1650 HP Water Brake Chassis Dynamometer
TD-36X3
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 22,000 lb (9,979 kg)Capacity: 1,650 hp at 45 mph (1,230 kW at 72 kph)Rolls: 36 by 31 in. (915 by 787 mm) 6 fixed rolls to accommodate axle spreads from 48 to 74 in. (1,219 to 1,880 mm) tandem centers and 50 to 64 in. (1,270 to 1,626 mm) tridem centersPit Required Depth: 35 in. (889 mm)
-
product
Four-Wheel Drive Dingle Roller Dynanometer for Cars with Axle Load of up to 2.4T, for Installation in an Existing LPS 3000 Dynanometer
MSR 500/2 CAR 4WD (LPS 3000) | VP 230038
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD is suitable for installation in an existing LPS 3000 base.
-
product
Brake Test Systems
Giant 8000 Series
Customer perception of vehicle quality is closely related to the NVH behaviour of the vehicle. With the HORIBA ATS Brake testing system, NVH relevant design features are analyzed and various metrics stored in the database of the automation system. For friction borne vehicle NVH problems coming from the brake and its components the GIANT 8000 Series is the ideal tool to resolve it. The GIANT 8000 Series is superior NVH test system providing you with the best testing conditions for all types of vehicles. Test brake fixtures could be tested with a complete wheel suspension system. In a semi acoustic chamber NVH tests could be realized and drum brakes and disc brakes including the vehicle axle could be tested.
-
product
Agriculture Solutions
The trend in agriculture: The drives of machines and commercial vehicles must be capable of transmitting increasingly high power within a limited space. Reproducible quality in series manufacture with the shortest possible production times are the key requirements in this industry.The hay makers and harvesters perform their task using straight bevel gears. Because the loads in these machines are comparatively small, a cost-effective manufacturing solution is crucial for the market success of straight bevel gears. It’s a different story as far as tractors are concerned: Spiral bevel gears are installed in the rear axles in this case – and the bevel gear set of a tractor’s rear-axle differential must transmit up to 400 kW. In tractors, cylindrical and planetary gears are also used in manual transmissions and counter shaft transmissions as well as planetary gear drives for transmitting power to the enormous drive wheels. These cylindrical and planetary gears must be efficient, quiet-running, and low-maintenance. With solutions from Klingelnberg, the entire portfolio can be produced on bevel-gear and cylindrical-gear machines.
-
product
Digital Roller Brake Tester for Cars and Vans up to 5.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,800mm
C_MBT C 5.0 W280 | VP 210160
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 5.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,800 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for large and heavy cars and vans, and with increased loads.
-
product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P | VP 230046
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P is also suitable for power measurements at constant speed and constant tractive force.
-
product
General Purpose Reaction Dual Shaft Torque Sensor
STS SERIES
The STS Series is our general purpose reaction type shaft torque sensor. They are often installed between devices such as motors, switches, shafts or axles, and their mounting plate to provide bi-directional torque output. They are available in six capacity ranges from 600 in-lb through 12,000 in-lb, and are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
Custom Bolt-On Strain Sensors
Our custom bolt-on strain gauge sensors are designed and manufactured to your application, based on your drawings and specifications, including all types of output formats. Ideal for dynamic load monitoring, capable of measuring and monitoring axle stress and weight with high accuracy.Do you have an application for strain gauge measurement that requires a quick and simple installation, repeatedly, in multiple locations? Perhaps you need a sensor with high environmental protection, which removes the necessity for time-consuming cleaning, complicated soldering and messy strain gauge adhesives?
-
product
Profiling Systems
ICK profiling systems measure, detect, classify, count, and check vehicles in 3D. They determine the number of axles on heavy goods trucks for vehicle classification and measure vehicle dimensions to rectify loading errors. The systems recognize overheated vehicles approaching tunnels and other entrances and activate diversions. They also monitor external train contours. If a limit value is exceeded, the system triggers an alarm. All this contributes to safety on roads and railroads.
-
product
622 HP Eddy Current Chassis Dynamometer
CM-51-EC
Weight Capacity: 25,000 lb (11,340 kg) per axleRoll Brakes: pneumatically-actuated discShipping Weight: 8,340 lb (3,783 kg)Capacity: 622 hp at 45 mph (464 kW at 72 kph)Rolls: 20 by 36 in. (508 by 915 mm) long4 front fixed rolls, 2 rear rolls fixed toaccommodate axle spreads from48 to 60 in. (1,219 to 1,524 mm)tandem centersPit Required Depth: 25 in. (635 mm)
-
product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P-PLUS | VP 230047
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P-PLUS roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P-PLUS is also suitable for power measurements at constant speed and constant tractive force.
-
product
Towing Dynamometer
RS-135K
RS-135K towing dynamometer is designed for testing off-highway construction and agricultural equipment. Built with a heavy-duty steel frame, industrial axles and rides on an air ride suspension, the RS-135K can maintain up to 135,000 Newtons of constant drawbar pull with the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there’s no lead-acid batteries to charge and testing is unlimited at low speeds.
