Filter Results By:
Products
Applications
Manufacturers
PD Test
partial discharge testing.
See Also: Partial Discharge, Partial Discharge Detection, Partial Discharge Monitors, PD, Partial Discharge Test
- Pickering Interfaces Inc.
product
Switching System Test Tools
EBIRST™
Switching systems are an important part of many test systems, however, the switching system is in a vulnerable place. When accidents happen that can cause a faulty device, you need a way to get the system up and running again with a minimum of effort and operator skills.
-
product
PD Measuring System
TEM
Partial discharge test system for laboratory or on-site measurement according to VDE 0434, IEC 60270 and EN50178 consisting of:*Partial discharge meter TMG*High-voltage coupling capacitors for decoupling of the PD pulses*Partial discharge calibrator TPK for determining the correction factor in the PD test circuit
-
product
Plastic Fabrications Testing Equipment
PD and PHD Pinhole/Holiday Detectors have an alarm circuit to alert the operator when a fault has been located and the required test voltage can be set on the unit's meter. Spark Testers provide an inexpensive means of testing but have no output voltage meter or audible alarm. However, they can test joints even if the backing is not connected.
-
product
Ethernet Powered Device Analyzer
PDA-604A
Emulate any 802.3at Type-1, Type-2, 802.3bt Type-3, or Type-4 PSE powering 2 or 4 pairs at all possible PD input voltages. Optionally supports 802.3at and 802.3bt Ethernet Powered Device Conformance Test Suites and LLDP Emulation and Analysis.
-
product
Gas-Filled Hv Testing Transformer
GTU-300KVA/600KV
Wuhan Sangao Electrical Test Installations Limit Co.
SF6 gas -filled testing transformers are especially designed for GIS in the factory and on-site test, and for testing all GIS switchgears and GIS components such as insulators, insulating tension pole, GIS voltage transformer and so on, the PD test can be performed under the general environment because of the merits of encapsulation, the PD level of our equipment can be lee than 3pC, and it can be added a HV bushing to perform the withstand voltage test at the same time. Small and compact dimensions resulting in minimum space requirements. Light-wight components. Rugged construction to withstand long transportation stresses. Direct flanging to the test object. High safety for tester because of encapsulation of all HV parts. Large range of application in conjunction with HV bushing for withstand voltage test. Built-in HV measuring capacitor and coupling capacitor. Built-in HV disconnecting switch to separate multipath test object connector to ensure the safety of HV testing.
-
product
Inflatable High Voltage Testing Transformer
GTU-250KVA/500KV
Wuhan Sangao Electrical Test Installations Limit Co.
SF6 gas -filled testing transformers are especially designed for GIS in the factory and on-site test, and for testing all GIS switchgears and GIS components such as insulators, insulating tension pole, GIS voltage transformer and so on, the PD test can be performed under the general environment because of the merits of encapsulation, the PD level of our equipment can be lee than 3pC, and it can be added a HV bushing to perform the withstand voltage test at the same time.Small and compact dimensions resulting in minimum space requirements. Light-wight components. Rugged construction to withstand long transportation stresses. Direct flanging to the test object. High safety for tester because of encapsulation of all HV parts. Large range of application in conjunction with HV bushing for withstand voltage test. Built-in HV measuring capacitor and coupling capacitor. Built-in HV disconnecting switch to separate multipath test object connector to ensure the safety of HV testing.
-
product
USB PD Test System
6050
Single Output USB PD USB PD basic version：the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
product
I2C/SPI Exerciser and Protocol Analyzer
PGY-I2C/SPI-EX-PD
Prodigy Technovations Pvt. Ltd.
I2C Protocol Analyzer and SPI Protocol Analyzer (PGY-I2C/SPI-EX-PD) are the Protocol Analyzers with multiple features to capture and debug communication between host and design under test. PGY-I2C/SPI-EX-PD is the leading instrument that enables the design and test engineers to test the respective I2C or SPI designs for its specifications by configuring the PGY-I2C/SPI-EX-PD as Master/Slave, generating I2C/SPI traffic and decoding the I2C/SPI protocol decode packets
-
product
Gas Filled Hv Test Transformer
YDQW-50KVA/250KV
Wuhan Sangao Electrical Test Installations Limit Co.
SF6 gas -filled testing transformers are especially designed for GIS in the factory and on-site test, and for testing all GIS switchgears and GIS components such as insulators, insulating tension pole, GIS voltage transformer and so on, the PD test can be performed under the general environment because of the merits of encapsulation, the PD level of our equipment can be lee than 3pC, and it can be added a HV bushing to perform the withstand voltage test at the same time.Small and compact dimensions resulting in minimum space requirements. Light-wight components. Rugged construction to withstand long transportation stresses. Direct flanging to the test object. High safety for tester because of encapsulation of all HV parts. Large range of application in conjunction with HV bushing for withstand voltage test. Built-in HV measuring capacitor and coupling capacitor. Built-in HV disconnecting switch to separate multipath test object connector to ensure the safety of HV testing.
-
product
PoE PD Test Solutions
Explore PoE PD Test solutions from Sifos Technology. What type of testing does your Power-Over-Ethernet Powered Device need?
-
product
PD Conformance Test Suite
Sifos Technologies offers the ultimate simplicity in testing a PD’s conformance to IEEE 802.3 Standards with Pass/ Fail reporting in the PD Conformance Test Suite available for purchase with the PDA-600 Family of Instruments.
-
product
Valves Testing Equipment
A PD or PHD Pinhole Detector is ideal as it has an audible alarm which sounds when a fault is found. Additionally, the test voltage can be set accurately, which is particularly important when testing thin linings. A DCCT mains-powered porosity tester can be used if the process needs to be incorporated into a production line
-
product
LLDP Emulation And Analysis
802.3at and 802.3bt PD Emulation and Protocol Analysis
*Integrated PoE LLDP and Load Emulation in a Single Instrument*IEEE 802.3at and 802.3bt LLDP Compliance Analysis*Independent, Per-Port 802.3at and 802.3bt LLDP Emulations*Flexible Single and Dual Signature PD LLDP Emulations*One-Click LLDP Protocol Capture and Analysis*Pop-Up Excel Spreadsheet Reports Assess Protocol Content and Timing*Enables One-Click Emulated Power-Ups and Standard Waveforms with LLDP Power Granting PSE's*Enables 2-Pair and 4-Pair PSE Conformance Test Suties with LLDP Capable PSE's*Enables 2-Pair Multi-Port Suite with LLDP Capable PSE's*Available for PSA-3000 and PSL-3000 Platforms
-
product
Partial Discharge
Partial discharge (PD) is a local electrical discharge that occurs in imperfections or inhomogeneities. The partial discharge measurement is a so-called “non destructive test” to determine the quality of insulating materials. On the contrary of pure high-voltage test, th test item is not pre-damaged at low PD levels.
-
product
Capacitive Divider
It can be chosen as PD sensor for Techimp PDCheck, PDScope or PDBaseII systems. It is suitable for on line or off line PD tests onrotating machines, for both spot measurements and monitoring applications. A BNC termination is available to connect the coupler through a coaxial cable.
-
product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
PSL-3424 Quick Test for 802.at and 802.3bt PSE's
*Accessible from PSA Interactive or PowerShell PSA*Scans 2 to 8 PSE ports per test cycle*Automatically determines and adapts to PSE maximum assigned class*Tests PSE’s that grant full power via PD Classification or through PoE LLDP*Validates PoE Detection Acceptance and Rejection Range*Measures PSE Port Voltage at both minimum (DC MPS) and maximum (Pclass) load conditions*Reports PSE type (AT vs BT), maximum assigned class capability, and Pclass power capacity*Assesses Disconnect Power Removal response*Assesses Overload Power Removal response*Assesses LLDP Power Protocol and Allocations (PSL-3424L)
-
product
HV Test Transformer
GTU-800KVA/220KV
Wuhan Sangao Electrical Test Installations Limit Co.
SF6 gas -filled testing transformers are especially designed for GIS in the factory and on-site test,and for testing all GIS switchgears and GIS components such as insulators,insulating tension pole,GIS voltage transformer and so on,the PD test can be performed under the general environment because of the merits of encapsulation ,the PD level of our equipment can be lee than 3pC,and it can be added a HV bushing to perform the withstand voltage test at the same time.
-
product
PSA-3000 / PSL-3000 Software
Included with every PSE test instrument in the PSA-3000 family are PSA Interactive (GUI) and PowerShell PSA (script automation) software. Whether running test suites, setting up PD emulations, analyzing specific PSE behaviors, or automating QA tests, PSA Software enables high productivity and rapid results.
-
product
1200kVA High Voltage Testing Transformer
GTU-1200KVA/600KV
Wuhan Sangao Electrical Test Installations Limit Co.
SF6 gas -filled testing transformers are especially designed for GIS in the factory and on-site test,and for testing all GIS switchgears and GIS components such as insulators,insulating tension pole,GIS voltage transformer and so on,the PD test can be performed under the general environment because of the merits of encapsulation ,the PD level of our equipment can be lee than 3pC,and it can be added a HV bushing to perform the withstand voltage test at the same time.
-
product
Gas-insulated AC Test System
Yangzhou Power Electric Co., Ltd
The test system is used to do AC voltage withstand test and PD measurement for high voltage insulation products, combined electrical equipment, instrument transformers, etc.
-
product
Partial Discharge Calibrator
TPK-H
The high voltage-resistant Partial Discharge calibrator is used to determine the correction factor in the PD test circui.
-
product
Inductive Sensor
HFCT Ø 30-39-50mm
Techimp HFCT is an inductive sensor for partial discharge measurements. It is suitable for on/off line PD tests on many electrical systems (cables, transformers, rotating machine, etc..). It has to be applied to the ground connection of the system to be tested.
-
product
VLF Testing and Diagnostics System
PHG 80 TD/PD
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PHG 80 TD/PD. With the PHG TD/PD, you get a multifunctional cable testing and diagnostics system that was specially designed and developed for medium-voltage networks. The PHG TD/PD system is also the only cable testing and diagnostics system that gives a comprehensive overview of the quality and ageing condition of the test sample. The diagnostic methods TD and PD are mutually complementary, because on one hand you can detect the complete condition and on the other hand locate individual faults in the operating resources.* High performance VLF truesinus testing device (3 kW) with regulated output voltage* Compact, enclosed design in 19" format* Variable installation option with separate control and voltage unit* Variable connection options to cable stations of different models
-
product
Laser Diode Drivers
Arroyo Instruments offers a broad range of laser drivers to meet your exact test needs. From 100 milliamps to 100 Amps, all of Arroyo Instruments' LaserSource benchtop laser drivers include unique features not found on competing products such as optically isolated photodiode and modulation inputs, programmable PD bias, and both RS232 and USB computer interfaces. The LaserSource also has laser diode protection circuits such as interlock, ESD protection, and hardware limits for current and voltage.
-
product
800 Kv High Voltage Testing Transformer
GTU-800KVA/800KV
Wuhan Sangao Electrical Test Installations Limit Co.
SF6 gas -filled testing transformers are especially designed for GIS in the factory and on-site test,and for testing all GIS switchgears and GIS components such as insulators,insulating tension pole,GIS voltage transformer and so on,the PD test can be performed under the general environment because of the merits of encapsulation ,the PD level of our equipment can be lee than 3pC,and it can be added a HV bushing to perform the withstand voltage test at the same time.
-
product
PD Test Systems
1. Number of channels: 2/4 electric signal interfaces & 1 EXT interface 2. Sampling frequency: maximum 200MGa/s 3. Sampling precision: 12bit 4. Range: 0.1mV~20V 5. Range switch: 1mV, 2mV, 5mV, 10mV, 20mV, 50mV, 100mV, 200mV, 500mV, 1V, 2V, 5V 6. Frequency band range: 1Hz-60MHz 7. Range non-linear error: 5% 8. Range of capacitance for test object: 6pF~250µF 9. Power source mode: internal lithium cell / AC 220V 10. Display: 6.5 inches TFT LCD 11. Resolution: 640×480 12. PV: 4GB 13. Hard disk: 32G stiff disk used for storing the test data
-
product
PoE Tester
PE-100
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotation between voltage (Volts), current(Amps) and power(Watts) via dual 4 digit 7 segment LEDs which provides voltage available, current flowing and how much power an PD actually need ensure sufficient power for PD to make the PoE is sustainable.
-
product
Tap Adapter
Techimp Voltage Tap Adapter is gender changer which allows the user to connect to the test tap (sometimes called power factor tap) of high voltage transformer bushings.While keeping the test tap well below the safety voltage level required by the manufacturer, the Tap Adapter lets the user to drain high frequency PD signals for diagnostic assessment of insulating materials.A synchronization signal can be derived as well.It is suitable for both single shot as well as continuous PD monitoring.Although it must be customized on the basis of the shape and dimension of the test tap (to be provided by the Customer), many models are readily available for the most established transformer bushings. A list of the presently available models is reported below.Several thousands of hours of operation are a guarantee of reliability and accurate design.
-
product
Handheld Online PD Detector
PD-SGS
BAUR Prüf- und Messtechnik GmbH
Quick identification of PD activities in switchgear and cable accessories. The BAUR PD-SGS handheld online PD detector is used to conduct rapid initial tests for PD activities on live switchgear. Potential weak points are immediately signalled acoustically and numerically.* Initial rapid condition evaluation of switchgear and cable accessories during mains operation* Ideal for quick checks of MV and HV switchgear* Two integrated sensors:TEV sensor records PD on the surfaces of switchgearsAcoustic sensor records PD inside switchgears* Greater safety for test personnel switchgear tested for safety risks before starting work
-
product
PD free AC Hipot Test Set
FPA Series
FPA Series test sets perform field or factory testing on larger electrical apparatus, including motors & generators, switchgear, bushings, bus duct, etc. This series offers the higher kVA ratings needed (0-6/12 kV AC @ 6 kVA), but is still packaged for portability.
-
product
Partial Discharge Measuring System
LDS-6
The Doble LDS-6 is a highly sophisticated digital measuring system for partial discharge detection and analysis. It is trusted as a valuable tool for factory and laboratory testing.The LDS-6 can be used to test a variety of high voltage apparatus. Use the LDS-6 to perform PD quality tests on motors, generators, transformers, MV and HV cable systems, switchgear and additional HV accessories.The LDS-6 complies with IEC 60270, VDE 0434 as well as various IEEE and other standards.
