Filter Results By:
Products
Applications
Manufacturers
Probers
Transfer and connect test target to contactor or move probes to target.
See Also: Probing, Probing Stations, Nano Probes, Flying Probes, Wafer Probers, Interrogation
-
product
High Voltage 50 Ω Pulse Generator
TLP-8010A
High Power Pulse Instruments GmbH
*Wafer and package level TLP/HMM testing*Fast 50 Ω high voltage pulse output with typical 300 ps rise time*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω-configuration*High pulse output current up to ±80 A (short circuit) with 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 300 ps to 50 ns*1 built-in pulse width: 100 ns*Optional external pulse width extensions 5/10/50/100/200/500 ns using an external pulse width extender TLP-8012A5*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
-
product
Memory Test System
T5230
T5230 memory test system for NAND/NVM devices adopts a combined array architecture to achieve best-in-class cost-of-test performance for wafer test, including wafer-level burn-in (WLBI) and built-in self-test (BIST). The system can perform on-wafer test of 1,024 memory devices per test head in parallel, delivering high productivity and enabling floor space savings of up to 86%. Multiple test cells are connected per system controller in the T5230, allowing independent wafer test of each test cell. The test cells can be stored in a general multi-wafer prober while minimizing the test cell floor space, and the tester can be docked with probers in both linear and multi-stack configurations. For functional tests at a maximum test rate of 125MHz/250Mbps, the T5230 assures high timing accuracy, repeatability, and failure detection capability.
-
product
Software
Gate Oxide Integrity Option
Materials Development Corporation
Oxide integrity of MOS devices can be evaluated by various techniques such as Time Dependent DielectricBreakdown, Charge to Breakdown, or ramped voltage. When used with a prober, map distribution of breakdown fields. Output the data using histograms, cumulativefailure, or Weibull plots.
-
product
Die Sorter Handler
4605-HTR
4605-HTR is a MAP Sorter which picks up devices from wafer ring and sorts to tape or bin according to the MAP file created by film frame test handler or prober. 4605-HTR is a high speed handling system, available for 12 inches wafer rings. When used in combination with 4170-IH, 4605-HTR much improves efficiency in testing process of leadless devices as a high speed sorting machine.
-
product
Low-leakage Switch Matrix Family
Conducting all the parametric measurements necessary for the numerous test structures on a semiconductor wafer can be a time-consuming and expensive process. With the cost of end-user devices continuing to drop, even laboratory characterization environments must reduce the cost of test. Until now engineers and scientists working on current and future semiconductor process technologies were faced with a difficult choice: either use a semiconductor parameter analyzer with positioners on a wafer prober, which limits the ability to perform automated test, or use a switching matrix and probe card, which reduced the analyzer's measurement resolution. Utilizing a switching matrix with a semi-automatic or fully-automatic wafer prober enables characterization tests to be automated, eliminating the need to have an operator manually reposition the probes each time a new module needs to be tested. This reduces both test time and cost. Due to the many price/performance points available, Keysight's switching matrix solutions provide the flexibility to choose exactly what your testing needs require, without overspending.
-
product
FPP Software
Four Point Probe
Materials Development Corporation
For use with a manual four point prober, the MDC FPP Software operates in a convenient, single screen that displays both measurement parameters and testresults. The FPP software can measure Resistivity, Conductivity, Resistance, Doping, Thickness, and SheetResistance when used with a compatible current source and voltmeter or SMU.
-
product
Probe System
Acculogic Sprint 4510
The Sprint 4510 family of flying probers are well known for their speed, reliability, ease of use and large world-wide installed base.Flying probe testers have few restrictions on access, require no test fixtures, and can test boards with virtually unlimited number of nets, allowing test developers to turn a program around in a short time.
-
product
Fully Automatic MRAM Probe System With Initializers
*This system can measure MRAM characteristics automatically.*Automatically initializes(resets) before and shorten the time of measurement by having a built in initializer.*Generates strong and constant magnetic fields. (Prober: Max 1.5T, Initializer: 2.7T (the highest in the industry)
-
product
High Voltage 50 Ω Pulse Generator
TLP-3010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±8 kV*High pulse output current up to ±30 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
product
Wafer Prober Networking System
PN-300
The Wafer Prober Networking System PN-300 utilizes a database to facilitate data access from other systems and provides an environment that enables the user to edit data and handle processing. The system achieves wide-ranging compatibility by adopting standard hardware and operating system. In addition, it is equipped with an N-PAF (Network-based Prober Advanced Function) to provide robust support for wafer prober operation and maintenance.
-
product
High Voltage 50 Ω Pulse Generator
TLP-12010A
High Power Pulse Instruments GmbH
- High pulse output current up to ±120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical 300 ps rise time- Wafer, package and system level TLP and HMM testing- 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 digital programmable pulse rise times out of: 300 ps to 50 ns (optional)- 1 built-in pulse width: 100 ns- Optional external pulse width extensions from 5 ns to 500 ns using the external pulse width extender TLP-12012A6- Built-in pulse reflection suppression- Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses- Efficient software for system control and waveform data management- The software can control automatic probers for fast measurements of complete wafers- Integrated interlock safety shut-down- Industrial isolated and EMI/ESD protected USB control interface
-
product
Probe Only Manipulator
LSP
The LSP mounts to standard prober hinge mounts with easy access to service and engineering locations. This reduces the floor space per test cell, saving you significant capital expenses. And you’ll be able to quickly and easily set up your ATE to wafer probe.
-
product
Flying Probe Test Systems
Flying probe testers work by In-circuit testing the board via a number of moving test probes. They have the advantage over traditional In-circuit testers of not requiring a dedicated "bed of nails" test fixture thus reducing the price for each different board being tested. However, modern Flying Prober testers offer so much more than just In-circuit testing. They enable the user to combine In-circuit, AOI, Functional, Device Programming and Boundary Scan testing, in one test system.
-
product
Coaxial Cable Termination Toolkit
ICFP
Ardent’s ICFP is a next generation coaxial cable termination toolkit for advanced system design de-embedding, de-bugging, and calibration. Designed for the lowest loss access to signal paths on an IC circuit footprint, this solution is a simple, cost effective alternative to expensive probers and x-y tables for Engineers who need to probe multiple signals at once.
-
product
Cryogenic 4K Probe Cards
Over the last 20 years the Celadon Engineering team has developed an expertise in cryogenic materials which has resulted in a solid reputation in the industry for producing extremely stable cryogenic on-wafer probe cards as well as DUT probing solutions. These Cryogenic probe cards have all the benefits of Celadon’s Crash Resistant™ probe technology but with the ability to probe as cold as humanly possible. Celadon’s cryogenic solutions vary from standard VersaTile™ footprints which interface to positioners to innovate custom PCB based designs to allow for flexibility when testing at these very cold temperatures. Lakeshore cryogenic wire is used in standard DC solutions for high density cable-out designs to support high pin count applications. During the development process, Celadon works closely with the cryogenic prober vendor to ensure the integrated solution is optimized for current and future testing needs.
-
product
MPI SENTIO®Software Suite
MPI Advanced Semiconductor Test
By using a novel approach based on simplicity and truly intuitive operation, MPI was first to develop a revolutionary multi-touch prober control software suite to address today’s challenges of operating complex test systems. It saves significantly training time and makes the operators’ life as easy as possible!
-
product
Full Wafer Test System
FOX-1P
Enables High Throughput, Single Touchdown, Full Wafer Production Testing. Capable of simultaneously testing up to 16,000 die in a single wafer touchdown. Resource configurable up to 16,384 " Universal Channels " - each programmable as anI/O, Clock, Pin Parametric Measurement Unit ( PPMU ) or Device Power Supply ( DPS ). Software-enabled per site flexibility to support small and large device pin count test needs. Comprehensive functional and parametric test capabilities Deep functional pattern data and capture memory optimized for BIST/DFT testing. Per channel PMU for per site parametric testing Individual channel over-current protection to protect wafers and probe cards. Configured for high volume production. Compatible with industry standard probers and probe cards. Available as an integrated test cell with prober, probe cards and 16,384 channel probe I/F. Configurable as a single or dual system integrated test cell.
-
product
Adjustable Clamshell Bed of Nails Testers
AdjustaBON Family
Designed for quick test development. This fixture can be configured to probe almost any circuit board in just a few hours. Once the perfect test is developed, move this light weight fixture out to the production floor to evaluate your production line test strategy prior to buying permanently drilled test fixtures, or while waiting for your drilled fixtures to be delivered. The AdjustaBON competes with the Flying Prober. There are many advantages over the flying prober. Setup is simple and intuitive and can be much quicker than programming a flying prober. Small size provides versatile bench top operation right where you need it. Maintenance costs are insignificant in comparison. The total cost of this fixture is in many cases less than the yearly maintenance cost of a flying prober. It would be possible to buy one of these fixtures every year for the price paid just to maintain one flying prober and it is about 1/20th the purchase price
-
product
On-Wafer Measurements
Accurate DC/CV (and RF) statistical modeling of semiconductor devices requires collecting a significant amount of measured data from different wafers across several temperatures. Keysight Technologies recommends IC-CAP WaferPro as a turn-key DC/CV and RF automated characterization solution to help modeling and device engineers achieve more efficient on-wafer measurements across temperature. This new breakthrough solution is based on IC-CAP modeling software and efficiently controls DC/CV analyzers, network analyzers, probers, switching matrixes, and temperature chucks, as well as the powerful 407x and 408x Series of Keysight parametric testers.
-
product
Automated Wafer Prober for Magnetic Devices and Sensors
Hprobe design and fabricate turnkey automated testing equipment (ATE) for electrical characterization and testing of integrated circuits under magnetic field such as MRAM (Magnetic Random Access Memory) and sensors. In each phase of the technology and product development as well as during mass manufacturing, a dedicated magnetic tester is available.
-
product
High Voltage 50 Ω Pulse Generator
TLP-4010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
product
Universal Manipulator
LSC
The LSC is a versatile universal manipulator, compatible with probers, vertical plane handlers, and dock-from-below test systems.
-
product
Cable Tracer Prober M-CTP-240A
Cable Tracer Prober M-CTP-240A
Fuzhou Metricu Technology Co Ltd
Cable Tester, network tester
-
product
WaferPro Express On-Wafer Measurement Program Software
WaferPro Express software performs automated wafer-level measurements of semiconductor devices such as transistors and circuit components. It provides turnkey drivers and test routines for a variety of instruments and wafer probers. Its new user interface makes it easy to setup and run complex wafer-level test plans, while powerful customization capabilities are enabled by the new Python programming environment.
-
product
EasyEXPERT group+ Device Characterization Software
EasyEXPERT group+
Keysight EasyEXPERT group+ GUI based characterization software is available for Keysight Precision Current-Voltage Analyzer Series. It is available on your PC or the B150xA's embedded Windows 7 platform with 15-inch touch screen to accelerate the characterization tasks. It supports efficient and repeatable device characterization in the entire characterization process from measurement setup and execution to analysis and data management either interactive manual operation or automation across a wafer in conjunction with a semiautomatic wafer prober. EasyEXPERT group+ makes it easy to perform complex device characterization immediately with the ready-to-use measurements (application tests) furnished, and allows you the option of storing test condition and measurement data automatically after each measurement in a unique built-in database (workspace), ensuring that valuable information is not lost and that measurements can be repeated at a later date. Keysight Precision Current-Voltage Analyzer Series provides the complete solution for device characterization with these versatile capabilities EasyEXPERT group+ is upgradable from the previous generation of EasyEXPERT/Desktop EasyEXPERT software.
-
product
Wafer Test
Automatic KLA wafer probers with tray-to-tray-wafer-handling are operated 24h a day and 7 days a week. Data retention bake/tests are done at wafer level
-
product
Precision Flying Probe Platforms For Automated Test Applications
Flying Probe technology is used to automate the testing of printed circuit boards (PCB) that would otherwise have to be tested manually. Adding a Huntron Access Prober to your test procedure will significantly decrease test times therefore increasing productivity.Access Probers can accurately place a probe on test points with high accuracy achieved using micro-stepping motors and linear laser encoders. Probing the smallest surface mounted devices is possible. Huntron Access Probers can automate your unique test process using the standard probe or by adding a custom probe of your design. Huntron offers three Flying Probe system configurations based on PCB size and test head requirements.
-
product
Wafer Prober
Precio XL
Fully automated 300mm wafer prober. The system achieves high productivity, excellent contact performance, improved cleanliness, and short lead time, and offers a number of high value-added functions as options.
-
product
Flying Prober Test System
QTOUCH2204C
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.
-
product
Wafer/Dicing Frame Prober
WDF 12DP+
The WDF 12DP is a prober/handler capable of transporting and testing standard 300-mm wafers and dicing frames without need of a changeover kit. To support multiple tests after dicing, it has a special positioning function that differs from former types, as well as image-processing functions such as wafer level packaging.
