Meltronics Systemtech
Meltronics Systemtech is a product creation company. As a technology solution provider, we offer services and turnkey solutions in the harsh Real Time and Strategic Electronics Domain spanning many industries like avionics, medical, transport, defence & industrial equipments.
- (080)28525400/01/02
- 080-28540787
- meltronics@meltronicsgroup.com
- 82, 1st Main, 5th Cross, A Block
AECS Layout
Kundalahalli, Bangalore 560037
India
-
-
product
Solar ATE
MS 1534
The Inverterless ATE is an automatic test equipment which is used to test the all functional and various test conditions of Inverterless Solar Unit. This ATE shall be a GO/NOGO Tester for Inverterless Solar Unit. All production units can be tested with this ATE for functional testing and clearance. This ATE reduces the man effort for quality checks and detects the failure units. The Inverterless ATE can check the UUT with minimum user interactions. It shall test and generate test report in PDF format for the conducted tests with necessary data. The ATE operates on 230V AC power. The ATE has In-Built AC-DC converter which provides 12V DC for operate the unit. Also it has additional AC-DC converter to simulate solar power to the Inverterless units. The main objective of the ATE is to test the Inverterless S in all possible test scenarios without external test equipments and less user interactions.
-
product
Intel 80486 DX2 Processor Board
MS 1500
- PC 104 bus and ISA bus interface- Facilitates design of scalable architectural solution for Embedded System- Back plane eliminated by self-stacking PC 104 bus- Substantial reduction of development time, cost, as well as risk- Helps to Faster time-to-market / timely product productions- Used for LCA Simulation Project- Intel 80486DX2 @ 33MHz- 512Kbytes of STATIC RAM, 2048 Kbytes of FLASH PROMS- 64 Kbytes of DPRAM- External Interrupts- RS232 Serial Interface- Watchdog Timer- External Bus Interface
-
product
RTM Actuator Signal Conditioning Board
MS 3630I
CPCI Rear IO Actuator Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on Primary and Secondary actuator interface. This card shall handle excitation signals, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
product
Signaling Control and Monitor Equipment
MS 1303
The Railway signaling unit is used to receive the input signals from the field for validating and clearing route for trains. After receiving the signals, signals are isolated and various tests are done inside the system to ensure the received signals reliability and produce clearance signal to railway line. For security reasons card signature has been given to each card in the system. System consists of digital input modules, digital output module, digital read back module, RS232 interface with 80486 processor board. It is an ISA Bus Back plane based system.
-
product
PCI Carrier Board
MS 1714
*64 bit PCI edge connector*64 bit PMC connectors*Operated frequency up to 66MHz*Regulated 3.3v supply to module
-
product
PCI Express To CPCI Board
MS 1719
PCI Express to CPCI card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit cPCI signals from/to the Host System. These cPCI signals are converted into PCI Express using cPCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
product
UNA Programmer
MS 1604
The UNA programmer is used to program the UNA board. The UNA Programmer is a processor-based system. The UNA Programmer performs the Blank checking, Programming, Reading and Verification
-
product
CPCI ARM LPC3250 Board
MS 1513
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
product
RTM Digital & Analog IO Board
*Bus Interface:- 16 Bit Data bus, 8 Bit Address Bus*Spartan-3AN FPGA based design
-
product
Intel x51 Based Boards
MS 1507
- General Purpose I/O Signals- RS232/422 Interface- External Bus, External Interrupts
-
-
product
CPCI Based 486DX4 Board
MS 1501
- CPCI/PXI Bus Interface, 6U form factor- Watchdog Timer- Hot Swap Facility- PCI Bus Rear IO Expansion for External Bus Interface- Debugging Monitor interface through RS232- JTAG interface for 486 for boundary scan test- Power Source through the CPCI connector J1 (±12V, +5V, 3.3V)- 1Mbytes of Dual Port RAM, 256Kbytes of STATIC RAM- 1MBytes of FLASH PROM- RS232, RS422 Serial Interface- Intel 486DX4 operating at 100MHz frequency at the core- Driver interface for Windows2000/XP/VISTA and LINUX/RT LINUX OS
-
product
High Speed Data Acquisition Board
MS 1800
*Bus Interface:- 64 Bit PCI Bus with PMC Interface*Virtex-4 FPGA based design*32 channel digital I/O signal*RS232 & RS485 Interface*32MB Flash*2MB Static RAM for data storage*Analog Inputs:- 2 Channel*Input Resolution:- 14 Bits*Sampling rate up to 80MSPS*Filter:- Low Pass Filter for all channels*Two Analog Outputs*14 bit Resolution*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
product
PCM Generator
MS 1607
The PCM Generator System used to generate different types of PCM format signals. The user can configure the PCM format to be generated. This system is an independent unit with LCD and Keypad for user interface. Primary application of the system lies in testing the airborne equipment.
