Finna Sensors
Finna Sensors is fully dedicated to manufacturing continuous on-line moisture measurement and control systems as well as handheld portable moisture analyzers.
- 909-941-7776
- 909-941-6444
- 9567 Arrow Route Suite #E
Rancho Cucamonga, CA 91730
United States
-
product
Model DC-2011: Cork Moisture Meter
DC-2011
Provides fast and accurate moisture read in 4% - 22% range. Durable plastic molded case, and includes Large LCD Display for easy reading. Reduces and eliminates factors such as cracked corks and poor cork compressibility, among numerous others. Product use reduces cork production error, increases efficiency, and thus increases profit.
-
product
Transverse HD Sawmill Meter
MC PRO 1500 HDNC
Finna Sensors built the Transverse HDNC Sawmill Meter to increase the number of potential sensors from 8 to 24. The sensors can now be specified to fit within chain runs and can be located on both the top and bottom faces. This significant increase in surface area allows mills to identify sapwood/heartwood boundary areas or wet pockets for proper sorting prior to kiln drying. Sorting by moisture content has been shown to improve drying productivity by 10% to 15%, as well as, enhance lumber recovery. Further advancements in the software allow users to track packages through the drying process, add Internet of Things (IOT) data and perform advanced analytics with new reports.
-
product
Model B: Concrete Moisture Meter
MRC003305
Specifically designed for the concrete block industry. Includes calibrations for over 34 different kinds of concrete block. Direct reading scales for average percent moisture content.
-
product
Model T8: Thin Materials Moisture Meter
MRC001970
Uses radio frequency capacitance to measure moisture. Provides average moisture content down to a penetration of 1/8 to 1/4 of an inch. Has three concentric rings that cover an area 3 inches in diameter
-
product
Model AM-IIIB: Paper Moisture Meter
AM-31B3
Portable digital paper moisture meter to measure single sheets. Permits instant and non-destructive moisture detection measurement on all types of paper and paperboard. Pre-programmed with 11 different Calibration Curved with option to select a field. Fast and accurate. Uses Radio Frequency to minimize effects of pH and temperature variations
-
product
Model A8: All-Purpose Moisture Meter
N/A
Designed for flat, curved, smooth, or rough surfaces such as cones or beams of yarn, rolls or stacks of paper or paperboard. Covers 3" a diameter (7.6mm) and penetrates 3/4" (1.9cm). Reliable, long battery life. Includes a rechargeable battery, carrying case, and operating instructions book.
-
product
Handheld Moisture Meters
Since water has a dielectric constant considerable higher than any other material, even a small amount of water in a product will cause the combination dielectric constant to increase substantially. Finna Sensors' capacitance meters can easily recognize this increase in water content and are programmed to display the result in direct reading percent moisture content.
-
product
Model LP: Lumber & Plaster Moisture Meter
MRC006504
Offers the same ad the Model L plus spring-loaded electrode buttons for testing irregular, flat, and curved surfaces. Allows moisture comparisons between kiln decks. Tests 1/4" (6.4mm) to 3/4" (1.9cm) thick wallboard and plasterwork.
-
product
SMART III RF Probe
Finna Sensors’ Smart III RF Moisture Probe is appropriate in those situations where NIR use on conveying systems/web applications or RF flat plate sensor use on board type products are not sufficient. Examples include tanks, bins, barrels, drums, Super Sacks™, silos, etc. These applications require a probe type moisture meter where the probe is inserted into, and is surrounded by product. Since the probe generates a 3 inch diameter radio frequency field around the length of the probe, a significant volume of product is measured. As the product is slowly removed from the silo, and refilled from the top, it passes by the RF Probe, thereby providing a constant real time moisture measurement. Typical applications would include starches, distillers and brewers grains, granulated chemicals or food ingredients, whole grains such as corn kernels, rice, soybeans, tree nut stockpiles, etc.
-
product
Model LGF2: Gypsum Moisture Meter
MRC006522-2
Two-range version of the Model LFG. Has 1/2 the normal sensitivity, allowing off-scale indications to be accurately read. Includes carrying case, NiMH battery and operating instructions book. Additional details can be found in product link.
-
product
Densigrader: Dynamic Weight Sorter
The Densigrader: Dynamic Weight Sorter is made for on-line mass/density measurements and sorting of green lumber prior to drying. The accurate mass and optional volumetric measurements provide an increase in grade recovery and kiln productivity. Its small footprint fits easily into most transverse, lugged transfer chains. System employs either RS232 or TCP/IP protocols to hand off data to sorting PLC.
-
product
Precigrader: Acoustic MSR System
Precigrader is an acoustic on-line strength grading system. The system is installed in more than 150 mills. It is used to determine common commercial grades in North America, including 1650 and 2100. A spring-loaded impact mechanism strikes the lumber as it passes. The resulting vibration is captured by microphones to determine the appropriate MSR grade.
-
product
Model DA-8: Digital Moisture Meter
552210
Provides instant moisture readings from 0% to 25% on a wide variety of materials such as gypsum board, yarn, and more. Stores up to 99 calibrations.
-
product
SMART III NIR Moisture Sensor
Rapidly analyzes the surface of material using near infrared technology. Ideal for continuous, non-destructive moisture measurement and coat weight in 0% - 60% range. Additional upgrades include scaling, grain control, auto-ranging and rapid calibration.
-
product
KilnScout-Softwood: Wireless Kiln Moisture Meter System
KilnScout-Softwood is an integrated wireless moisture system for batch and continuous kilns. The system provides real-time moisture measurements for drying optimization and control strategies. Each sensor measures 17 cubic feet providing an accurate representation of product moisture content during drying.
